Search results

  1. alldodge

    5.7 slave cylinder wiring

    Measure from I to case ground, should read 0.00 ohms If you get something higher then it may go thru the coil
  2. alldodge

    5.7 slave cylinder wiring

    Agree FT has it 1 & 2. Put small Y/R wire on the I terminal and Black on other one. The coil needs a ground and in most cases doesn't care if it's on the "I" side or the other. Being DC it will still energize 3. The wires should go to the ALT as you listed unless the ALT was replaced with a...
  3. alldodge

    1976 Montego 16- The "Free" Puppy

    No reason to not leave it open. Do see if there is a drain and if should not be clogged
  4. alldodge

    Jabsco 37010 not pumping water in

    The valve may not be there, and if so then it wasn't needed for original install Agree with dingbat, if pump will not pull water then there is probably a air leak, either that or the impeller is not making good contact. There are different impellers, you sure you have the correct one?
  5. alldodge

    no electrical systems working

    Is the motor a GL and if it's a GL- which one?
  6. alldodge

    no electrical systems working

    Welcome Need to start tracing wires with a voltmeter Which 5.0 is it?
  7. alldodge

    I just got this rope and it has some frays.. Think it's OK to use??

    Always use Poly for any kind of toy, it floats, and you want it to float I would not use dyneema with toys, main reason is it's stronger then steel. While poly may not break if it gets wrapped around a limb, it has a better chance of not cutting it off. Case in point, gal got ankle tangled up...
  8. alldodge

    Jabsco 37010 not pumping water in

    Don't know much about them but manual shows a vent loop and vent solenoid. Does the raw water come from over board or fresh water tank? This manual shows loop on page 2 https://www.pumpagents.com/pdf/JabscoPumps/37010-0090.pdf
  9. alldodge

    Mercmonitor First Power Up - "Warning No Starboard Engine" (part 2)

    This is a write up I have saved Hello Folks; I have a 2006 Chaparral Signature 350 with twin 496 MAGs. Not originally equipped with vessel view or any SmartCraft accessories despite the engines being capable. I added a NMEA bridge to allow my Garmin ChartPlotter (7610xsv) to display engine data...
  10. alldodge

    Alarm capacitor 4.3L

    correct
  11. alldodge

    What does this marking mean on this new to me outdrive?

    AK - sound my cat makes when hacking up a hair ball
  12. alldodge

    I just got this rope and it has some frays.. Think it's OK to use??

    That kind of line is used for water sports, should not be used where a higher level of safety is needed. Many use it for dock lines, fenders and such I don't see any issue other then wonder what caused the damage
  13. alldodge

    Closed Cooling System Part # 860234A1

    Pic would help but my guess is the belt is not routed correctly Most serpentine belts rotate the circulating water pump in opposite direction of the crankshaft
  14. alldodge

    1984 Mercruiser 3.0 starter wiring help

    Welcome The pic has an error. Put orange wire on the white plastic fuse.
  15. alldodge

    Mercruiser 5.7 with V6-14 TB IV module??

    TB 4 and 5 get full time 12V when key is ON or when motor is cranking. So check to make sure your getting 12V full time
  16. alldodge

    Mercruiser 5.7 with V6-14 TB IV module??

    You have the old style which is classified as a 2 wire The kit comes with terminal connections to make it go from old to new style
  17. alldodge

    leak from deck to inside boat above waterline

    Welcome When talking about a specific issue it's always best to provide as much info as possible and pics in this case might help Not seeing what your issue is, I would think 3M 4000 maybe
  18. alldodge

    Mercruiser 5.7 with V6-14 TB IV module??

    The distributor sensor should have one white/Red, one white/green and one black wire https://www.amazon.com/Mercury-Marine-Mercruiser-ASSEMBLY-IGNITION-87-892150Q02/dp/B07GD475RM
  19. alldodge

    Sea Water Pump Cover - Question

    Don't have your motor serial number but O ring should be item 3 https://www.mercruiserparts.com/bam/subassembly/31601/4835/170
  20. alldodge

    Mercruiser 5.7 with V6-14 TB IV module??

    If your ignition sensor doesn't have 3 wires on it then I would suggest replacing it. The older 2 wire sensors were hit and miss. This is why the 3rd wire was added to make a better ground connection
Top