Search results

  1. R

    1971 mercury 500 thunderbolt (50 h.p.) ignition

    Belt timing checked?
  2. R

    Mid 70’s OMC. No spark.

    Post ohm reading of brown wires from stator.----Post ohm reading on one brown to ground.----Post ohm reading of sensor coil.
  3. R

    Mid 70’s OMC. No spark.

    A 1978 50 HP Johnson.
  4. R

    New Stuff on Vehicles likes/dislikes

    Not easy to find pre 1980's car in the " rust belt " areas.----just like outboards the older stuff is easier to maintain in your backyard.
  5. R

    New Stuff on Vehicles likes/dislikes

    I learned to drive long ago.---No sensors in the car because driver had the common sense back then.------I hate the " high tech " features that are big $$$ to repair.----If you hit a moose or deer it can mean a " write off " of the vehicle.
  6. R

    How should propeller “leakage / water seepage at the shaft seal” be addressed?

    Is it packing in there?----That can be adjusted to get the proper amount of leakage.----A mechanical seal should be replaced.----Pictures of your set up ?
  7. R

    1994 140hp evinrude

    Sparkplugs are not used for this test.----Buy a spark tester.----Or use some wire / glue and carboard to make one.
  8. R

    1979 Evinrude 4hp gear oil and cooling?

    It was stated that there is only 1 screw on this gearcase !!----Same gearcase as was used on earlier 2 HP motors.
  9. R

    Oil/fuel leaking from water intake Merc 40 4cyl 2S

    Pressure test the gearcase to see if there are any leaking seals.----Or just simply install a seal kit so you will not lose any sleep.
  10. R

    Need help, shift shaft height for 1996 15 hp Evinrude

    ????----Post #2 is very clear I believe.----No mention of any measurement.
  11. R

    Need help, shift shaft height for 1996 15 hp Evinrude

    The lower shift rod MUST be screwed in all the way then backed out so bend faces forward.------And the notch in the shift rods MUST be lined up with the hole in the connector BEFORE you put the screw in.----It really is as simple as that.
  12. R

    1000 hp pontoon

    Factories build stuff that people will buy.----Simple as that.
  13. R

    1994 140hp evinrude

    Nobody can see, touch or hear your motor !----You need to post information.-----The 2 most elegantly tests are #1 compression test, post the actual values here.---#2 is a spark test , does spark jump a gap of 3/8" or more on each lead, yes or no?----Then again it could be the flywheel key...
  14. R

    1979 Evinrude 4hp gear oil and cooling?

    Hole in the gear case down to drain.----Hole up to fill.----Do not use grease !-----Install a new impeller if you do not know how old it is.-----Water spits out with exhaust relief at the back of exhaust housing.
  15. R

    1980's serial number / harness / general questions

    The decals are for the 1976 model year.----What HP is this motor ?-----No chokes , as it appears to have an enricher unit.---serial # makes it 1985 for a 175 or 1982 for 200 HP near as I can tell.
  16. R

    Oil/fuel leaking from water intake Merc 40 4cyl 2S

    It may well be normal for a 2 stroke.-----Some gas / oil goes right through the motor without doing anything.
  17. R

    identifying part(s) found under mounting plate

    Nonsense.----The pulse limiter is a " flow fuse " for the VRO.----And the pulse limiter is NOT a " one-way valve" either.
  18. R

    identifying part(s) found under mounting plate

    Air comes through the pulse limiter and not fuel.
  19. R

    identifying part(s) found under mounting plate

    Look like the fasteners (317223 ) used to hold appliques on the cowling.
  20. R

    1988 Johnson 70hp inspection

    Post pictures of pistons after you open it up.----Need to try and determine what happened.
Top