Search results

  1. alldodge

    2002 Volvo Penta 5.7 Throttle body issues, Help!

    Did you find out what was causing the beep from your other thread? This one as with the other we don't know exactly what ECM is on the boat without a serial number. But ok you don't know and are unable to find, so we will go with what we have What psi? Need to know what the high pressure...
  2. alldodge

    Diagram for coolant system?

    No vid or book. Other then items as Buster mentioned, need a marine head gasket, brass or stainless block core plugs, and marine circulating water pump.
  3. alldodge

    5.7L MerCruiser Bravo III under water...repairable?

    That's a Bravo 2 and since the motor has been under water, its junk.
  4. alldodge

    Digital Throttle/Shift (DTS) Shift Adjustment ???

    Might just be the joy stick
  5. alldodge

    hot water tank smell/replacement

    Egg water, Tim Allen comes to mind
  6. alldodge

    3.0 exhaust manifold question.

    Yes and maybe Rust just shows it is leaking, but doesn't say how much. Its leaking it needs to be fixed, so remove and inspect To find out if this is doing it, place boat in water and see how much
  7. alldodge

    5.0 mercruiser 0M361530 carb

    SN shows Merc 2 BBL Have you replaced the filter (item 4) inside the carb? https://www.mercruiserparts.com/bam/subassembly/31837/2697/90
  8. alldodge

    Mercruiser Alternator Issues and Wiring

    Guess I don't understand the comment. The pics above "are" mando ALT Here are different ones including 2 different Mando's
  9. alldodge

    hot water tank smell/replacement

    The rotten egg smell is from old water not being flushed out. Take a mix of bleach and water and fill it up. Cap the lines off so it doesn't get into the rest of the system. Bleach can be hard on pump vanes and seals. Run the boat around getting into some bouncing. Drain, flush with fresh...
  10. alldodge

    1987 Mercury 2 Stroke Steady Beep

    It will have wires coming out somewhere, most likely on the bottom. The wires go to a float switch inside the tank. One of the wires should connect to the Tan/Blue and the other goes to ground. Unplug or disconnect either will stop the beep "IF" this is what's causing it to sound
  11. alldodge

    2000 FW 238 Vista VDO

    My 94 VDO gauges have held up very well and like the way their built. Many have used Autometer
  12. alldodge

    1987 Mercury 2 Stroke Steady Beep

    The Tan/Blue goes to your sensor switches. If anyone of them close this turns the beeper on. I see what looks like a oil tank (oil injection) and it would also go to it. If oil switch thinks the tank is low it will close. Unplug it
  13. alldodge

    How to remove seized carb main jets

    After reading what you have I would replace the carb Should also be in OB section
  14. alldodge

    Mercruiser Alternator Issues and Wiring

    Your number 2 should be ALT to Bat (orange wire) from where I see it being a Mando ALT
  15. alldodge

    Bogging issue solved with spark arrestor and fuel pick up screen

    Look thru the vanes on the arrestor, can you see clear thru?
  16. alldodge

    Mercruiser Alternator Issues and Wiring

    Wiring for your motor showing the fuse
  17. alldodge

    Mercruiser Alternator Issues and Wiring

    The Black is a ground, and I would install it under one of the nuts holding the slave relay in place. It may have been removed before and not reinstalled. Could have also been at another location, but it needs to be grounded to the block. With a bad ground it can cause the ALT to over charge...
  18. alldodge

    Volvo-Penta 3.0 - water in oil and other issues.

    With compression numbers above 150 I would say the cylinders has some water or other liquid in them, either that or the gauge is off Unable to tell from block codes, not able to find a listing What year is the boat?
  19. alldodge

    2004 Mercruiser 5.0 MPI Starting/Stalling Issues

    The 800 to 1200 would have me looking at the IAC and TPS. Noted you just replaced IAC and did you clean or replace the IAC muffler (foam rubber piece in TB)? At idle the TPS voltage should read about 0.5V Most likely your going to need to get some readings to determine what's going on...
  20. alldodge

    Trim not work above 3000rpm (377Mag MPI DTS Axius)

    Would be a question for @muc or @Fun Times
Top