Search results

  1. S

    Impeller change level of difficulty Q

    If nothing is crusted up it's fairly straight forward if your mechanically fit. Must be 100's of videos online.
  2. S

    Engine power loss

    Read post 4....
  3. S

    Johnson 25 hp hood part needed

    Used wise, there's probably millions. What's wrong with yours? Plastic mounting holes break?
  4. S

    Johnson 25 hp hood part needed

    The whole cowling...or just the head badge?
  5. S

    2011 15hp HO Evinrude

    You can wait and talk with Crosby man but you can go to the etec repair website at barnacle bills and search out your model. Probably a plugged pump.
  6. S

    2000 70hp johnson.

    I know you ground the tan wire....grounding the sensor would do nothing. I agree though not familiar with the quick start or does the key have to go on after? I already had the key on. It couldn't possibly matter. Horn goes off on test when you turn the key as it's supposed to. I never over...
  7. S

    2000 70hp johnson.

    Yeah, did that and nothing. Overheat has two wires, brown and a white wire.
  8. S

    2000 70hp johnson.

    Trying to test the overheat and oil alarm on this motor....anyone remember the procedure? I have a factor manual on the way.
  9. S

    Need control box

    I had to open mine to change out the shift/throttle cable and then had a heck of a time getting it back together. Got it back together about two times but the warm up throttle wouldn't work. I looked down kind of wiggled some things and I saw that two screws were loose pardon the pun. Tighten...
  10. S

    Johnson 150/175 carb saw

    I've got a GT 100....
  11. S

    Tilt running

    Should be one on the motor as well.
  12. S

    Need control box

    What going on with yours? Must be the black one. I was in one yesterday.
  13. S

    1991 60hp VRO Evinrude - No Spark

    Nice!
  14. S

    Johnson 150/175 carb saw

    Yes, check fuse located near starter solenoid. Rubber boot it in. If it's good probably bad or corroded wires. Always wondered what the "GT" stood for?
  15. S

    1986 Johnson 6.5hp Questions

    Well I'm hoping that "cottage" is sitting next to a lake. It's needs to run. Start at one and a half turns.
  16. S

    Need your opinion about replacing the original Reed Valves in my 1986 Evinrude 30 hp.

    I've had poor luck with ngks even though there's many on here that like them. Come up with your own opinion. Lean the two-stroke oil back, change the plugs possibly get an electric motor to troll with.
  17. S

    Engine power loss

    Most likely it your pickup screen in your tank....not your vent. Put a portable tank in and test. If that does it, install a spin on fuel filter and remove the screen from the pickup tube. Do you run ethanol fuel in it? Do you fill your tank during the off season. How your gas cap....I must...
  18. S

    1980 E100 motor issues

    Sounds like it's not running on all cylinders.....could be the video. It should "pop" more and a deeper tone.
  19. S

    1986 Johnson 6.5hp Questions

    Well I'm not sure on the commercial motors but I want to tell you a few things. That has a hand manual primer not a choke. Are you using that on cold start up? Are you familiar with the 3 positions? Are all the tubes good and in place? At the end of the tiller you should be able to adjust the...
  20. S

    Need your opinion about replacing the original Reed Valves in my 1986 Evinrude 30 hp.

    You don't need a timing light. Takes me about 3 times to get it right where I want it I'm afraid to say.
Top