Search results

  1. S

    Evinrude 50 impeller

    Grease is another example of holding parts together during assembly.
  2. S

    40hp Dead Top Cylinder

    Spark plugs and even the air would prove that!
  3. S

    Evinrude 50 impeller

    Also, down above the midsection....follow the lincage I believe....been a while since I worked on that size. I have one, I'll look at it.
  4. S

    Evinrude 50 impeller

    You will be fine....you don't need much if any.
  5. S

    No power from ignition switch

    Those bad grounds are a pain!
  6. S

    Short shaft to long shaft

    On most motors besides shift and driveshaft change it's water pump draw tube that becomes the hassle. Lots of options though
  7. S

    40hp Dead Top Cylinder

    You say the same things over and over and over and over.....I feel sleepy. Reeds don't follow carbs....I can't even remember what your problem is. All's I know is you have gas on your hands and you were advised to....what? Best to go see Mr Evinrude service man.
  8. S

    Sputtering out and dying

    What you say is true the fuel pump is not going to help. Pretty sure you just tried too many things on this motor instead of focusing on what was really wrong.
  9. S

    Evinrude 50 impeller

    I use snot....with dirt. I loan and borrow my friends tools constantly. Always returned better than when I or they got them. It's a West Coast thing! 😆 Seriously though, if it's a nice motor, go by the book. If it's one that you brought back to life with an unknown life expectations? Use...
  10. S

    Sputtering out and dying

    After it dies what do the spark plugs say to you...."we are wet? Or, man we're dry!" Does it lean sneeze and die or other.... Try choke or cupping carb/fuel spray? Right now you are guessing and throwing parts at it, you sound desperate. I'm sure Mr Wilson will chime in soon.
  11. S

    Evinrude 50 impeller

    Any miracle goo in a tube but best to use marine grade. I find these work well to hold the gearcase if needed.
  12. S

    1987 40hp evinrude vro (oil deleted) carb issue?

    Try pumping the primer ball when it starts to bog out....if it returns to normal then your guess is correct.
  13. S

    1987 40hp evinrude vro (oil deleted) carb issue?

    Sounds good really. Sneeze but your idle is low I believe.....set the idle in the boat running. After a zip around the lake, she probably will clear up because that's how they were designed. I forgot to send this...it was made several days ago.
  14. S

    Johnson 20 hp. Carburetor problem

    Link and sync is not correct. Move the cam 1/4 to 1/2 inch forward of the lines.
  15. S

    Fuel Tank F Up

    I use 3/8 hose ...did you install a spin on filter? What type of hose did you use? Not the gray crap I hope. Did you purge and out first?
  16. S

    1998 50HP SPL Poor performance at low engine speed

    Put an unlit propane torch next to the carb shaft and see if it revs up.
  17. S

    Gear shaft not engaging neutral (E8RCRM / Evinrude 8 HP 1984)

    Sounds to me like you slightly pulled the shift shaft out....could this have happened? If so we can tell you how to put it back.
  18. S

    40hp Dead Top Cylinder

    timsoutboard.com This is a recommended site that this forum promoted. They have always done me well.
  19. S

    40hp Dead Top Cylinder

    Clean or rebuild it properly or buy one from anywhere really. Cheap.
  20. S

    40hp Dead Top Cylinder

    What does this even mean? He changed the carb and the problem followed.
Top