Search results

  1. S

    2006 Johnson 9.9 four stroke J10EL4SD…

    Ok, might not be the best person here but let me get you started and others will chime in. First a few questions. The wire colors you stated above are on the motor side rubber plug that goes to a remote harness, right? Let's list what you need. You can install a momentary start button on the...
  2. S

    Best way to free steering cable retainer nut stuck on tilt tube shaft

    Yikes, some stuff I can't even understand. Top says nut is loose and down a little ways says no deal. Nut is stuck. Pretty sure where you put the vise grips does nothing. Picture would help. Even if you cut the cable you still have to deal with the nut to get a new one on so not sure how to...
  3. S

    2006 Johnson 9.9 four stroke J10EL4SD…

    Well a few questions, so your motor was not a tiller motor right? It had a remote and you really don't need it? This motor has a charging system correct? Will you be using that? Seems like more of a kicker motor. I think I can piece what wires should work for you.
  4. S

    2006 Johnson 9.9 four stroke J10EL4SD…

    Try this maybe? https://watercraftmanuals.com/outboard/johnson/manuals/johnson-5006590.htm
  5. S

    Looking for outboard mechanic in south nj

    Yes, what is your idle set at?
  6. S

    50HP evintude tiller fuel connector question

    Omc never went back to the 50 to 1 mix. They used the vro until they went to fuel injection. VRO was a good system.
  7. S

    1975 Johnson 25hp compatibility

    Are you sure it's not the prop?
  8. S

    1970 4HP Johnson

    Owned the Evinrude version....the only problem with that motor is forward gear only. You start it in gear and be prepared to go somewhere. Better as a trolling motor on say a 14 alum boat with a bigger older main motor that doesn't like to troll. Oil mix is richer on that motor too depending...
  9. S

    50HP evintude tiller fuel connector question

    I've had 3 vro outboards from omc. Never a problem. One needed rebuilding once but the alarm went off and no engine damage. Big technological advancement when it was made and I think omc followed Yamaha on that.
  10. S

    How to manually raise 1974 Mercury 85 with power trim

    Well, someone else's problem now. Hopefully someone can get some use out of your Dad's old engine. Many good memories Im sure.
  11. S

    Boat and motor given to me

    It varys the oil ratio from 100 to 1 at idle to 50 to 1 at WOT. Really helped 2 strokes run better and cleaner on the lower rpm's. Some people removed them and mixed 50 to 1 in their tanks. Do you still have a bottle in the engine or mounted in the boat?
  12. S

    OMC Serial Number

    Serial number won't help. Post pictures and someone most likely can tell about what year it is by looking at it.
  13. S

    suzuki dt85

    What video?
  14. S

    1957 fd-11 johnson skeg part number?

    You can grind and polish.
  15. S

    1957 fd-11 johnson skeg part number?

    What's wrong with yours? Post a picture perhaps.
  16. S

    over heat alarm 150 hp Yamaha 4 stroke 2006

    Anyone say why the overheat alarm was going off?
  17. S

    1977 evinrude 15hp water flow

    Sounds normal....remember those are just exhaust relief holes, most of your exhaust is going through the prop.
  18. S

    Boat and motor given to me

    Maybe start with pulling the spark plugs, inserting some 2 stroke oil and hand cranking it 10 to 20 times. Could be locked up.
  19. S

    1957 fd-11 johnson skeg part number?

    Somehow I missed the big red sign! Sheesh.
  20. S

    1957 fd-11 johnson skeg part number?

    Weird really. I found this but not sure where it even is. https://www.nlamarine.com/products/johnson-evinrude-18hp-outboard-fd-12-1958-gear-case-382832-377117-lower-unit?variant=11287772677
Top