Search results

  1. rolmops

    Electric connections for a 2024 9.9 Suzuki

    So I bought a nice Suzuki 9.9BTXW5 with side mound remote control for trolling for salmon and I am about to install it. The electronics from the side mount do get me quite mixed up. There is the connection that goes straight from the side mount to the engine, that I presume holds the start/stop...
  2. rolmops

    Penn or Cannon?

    I have been servicing and fixing my downriggers over the past few days and at this point I have 6 good working ones. 2 Cannon mag15s and 4 Penn 825s. I rebuilt all the motors and everything works fine. I would like your ideas and preferences between Cannon and Penn and why you have...
  3. rolmops

    combining a tailfin/powertran with a power pro 3.

    So about a year ago I bought a tailfin remote control kicker steering setup and I was not overly happy with it because fine tuning the remote control speed was an issue and I still had to do the speed control from the front end of my Islander. So what to do? I bought a powerpro 3 remote control...
  4. rolmops

    remote control tiller steering question.

    Here goes. I have a tailfin (powertran) remote control wireless steering setup and a powerpro 3 wireless speed control both for the same kicker. I need 2 remote control fobs to run this setup which I do not like very much. So I tried to hook the tailfin actuator into the powerpro 3 and now...
  5. rolmops

    Tohatsu wiring and trollmasterpro 3

    I installed a little remote control servo ( trollmaster pro 3) on my 2020 9.9 tohatsu and it works well, but not great.The troll master unit has a wire that is to be connected to a switched positive wire so there is no battery drainage when when the little engine is shut off. It makes no sense...
  6. rolmops

    troll master pro3 works with tailfin?

    I have a powrtran tailfin wireless kicker steering setup ,and I want to hook it into the troll master pro 3 wireless setup. Is this possible?
  7. rolmops

    replacing cabin starboard window on a 1989 starcraft islander

    If you did this, did you use 3/16 or 1/4 inch thickness ? Did you find the correct rubber to put around the window or did you have to use a generic material? Thank you for your help.
  8. rolmops

    Delco EST conversion kit timing problem

    This is about a 1989 4.3 liter OMC Cobra ignition conversion from points to EST distributor Conversion Kit. I have changed from points to est on several engines and in the case of the 4.3 liter you have to start the engine, let it warm up and then connect the base timing tool too a positive 12...
  9. rolmops

    rpm signal wire and est ignition

    I am rebuilding the dashboard on my Islander and bought an Artilaura rpm gauge. The directions say to connect the rpm signal wire to the negative side of the coil.I have an AC Delco est ignition and coil. I have no good idea where the negative side of the est coil is. Any help is appreciated ...
  10. rolmops

    1989 Starcraft Islander 221 (4.3 Liter) doghouse rebuild.

    I have just about finished the complete overhaul of my Islander , but I have no idea about fixing the doghouse. Does anybody have some pointers to rebuild that doghouse? If possible with measurements and/or pictures. As always, thank you very much for your opinions and advice. Cornelis
  11. rolmops

    Flame arrester stud

    Does anybody know the parts number of the 1989 4.3 liter Rochester carburetor (twin barrel) flame arrester stud?
  12. rolmops

    Starcraft Islander 221v fuel consumption.

    What sort of fuel economy can I expect with this Islander running on a completely rebuilt 1989 4.3 liter OMC Cobra (Michigan Motorz 2022 ). I am used to a 140 horse 4 cylinder mercruiser which I am told only "sips" fuel. I don't race all over the place, but I am curious to know what to expect...
  13. rolmops

    power steering cooler on a 1989 4.3 liter cobra

    I am trying to take advantage of the incredibly warm February days here in West New York and working on the 4.3 cobra. Right now I am trying to reattach the power steering cooler to the back of the block, but I forgot where to exactly bolt it onto. Is it the same place where the gear bracket is...
  14. rolmops

    windows for Starcraft Islander 221

    I am restoring a 1989 Islander and the starboard side cabin window is broken. What can I do to replace this? Any ideas? Thank you Cornelis.
  15. rolmops

    Alignment after transom replacement 1989 Cobra

    So I replaced the transom on a new to me 1989 221 Starcraft Islander and dropped my new 4.3 liter engine in. Everything looked fine until I tried to insert the alignment tool. It did not want to go into the coupler. I very slowly adjusted the front bolts from the very top to the very bottom, but...
  16. rolmops

    est ignition on a 1989 4.3 liter cobra.

    I bought a 4.3 longblock from M.Motorz and I put a new starter a rebuilt carb a new pump and a new alternator . Basically a new engine. So I want to go from the old points ignition to a delco est ignition just like on my 4 cylinder mercruiser where it works great. My problem is that I cannot...
  17. rolmops

    Changing the ignition on an 1989 4.3 liter omc Cobra from points to Delco EST Ignition

    I bought a 1989 Starcraft Islander 221. It is the type of boat I always wanted. Easily towable and big enough to feel safe on Lake Ontario. When I bought the boat, it was in "fair" condition. At least it does not leak. Just so I don't have to worry about getting stuck on the water, I bought a...
  18. rolmops

    Mercruiser remote control box replacement on Islander.

    I have a 1986 Islander with a fully rebuilt 3 liter mercruiser..(2021) For years I used a quicksilver commander 2000 (side control for outboards) but I feel that it is time to replace it as it is getting real cranky and worn out. I would like to put in a remote box with tilt and trim that has...
  19. rolmops

    35 hp Evinrude 1986 to be woken up.

    So I got back into playing with outboards a little bit. I have a 1986 OMC with CD2 power pack. The last time this thing was run, was for 10 minutes in 2003 in Cape Cod bay and pulled off the boat because of a lower unit problem. (it kept on dropping out of gear). Next it spent 17 years in a...
  20. rolmops

    oil filter for 9.8 hp tohatsu.

    Does it have one? If so where is it and what type is it? Thank you
Top