Search results

  1. nola mike

    Bad Upholstery a Deal Killer?

    Those seat bases are rotted. Guaranteed that the stringers are shot. Wouldn't be jumping at a Force 85 either if it's me. Hard pass.
  2. nola mike

    Deck Repair - Fiberglassing Question (Newbie)

    I'd suggest you core the foam as well, to the hull (PVC pipe works well for this) and check out the the nearby stringers thoroughly (including/especially the bottoms). Not sure how you'd eval the stringers without taking a core sample there as well.
  3. nola mike

    Engine alignment ,just got the tool. Pics posted

    Easy to measure, but people in general have had good luck with the eBay tools
  4. nola mike

    Banking Software

    I think there are free web based apps? Mint.com etc. I've been using kmymoney on Linux for many years. They have windows and Mac versions as well that I haven't tried. Downside is that the banks several years ago made it difficult/impossible to import account info automatically (I haven't tried...
  5. nola mike

    Engine alignment ,just got the tool. Pics posted

    I think he's getting spline marks, his "friction marks" are where the grease is wiped clean. Don't overthink it. Again, the important part is ease of insertion. The marks guide you as to which direction you're off if insertion is difficult. If you don't insert/remove the bar straight you can...
  6. nola mike

    Bah. Water in bellows.

    My understanding was that this seal was to keep grease in the bearing and wasn't needed on a sealed bearing. Although I did replace the seal when I replaced the bearing a few years back. I'm still thinking it could get through that way with those broken orings though.
  7. nola mike

    I wish I thought of this.

  8. nola mike

    Bah. Water in bellows.

    Just replied above. The shift seal/bushing isn't new, but it is the newer retrofit. Not sure how to test short of just replacing it. Quad ring was in place. Yeah, I don't think it ever got that high since last check. So unsatisfying. I won't have the patience to wait till the end of the...
  9. nola mike

    Bah. Water in bellows.

    Those are indentations from the retaining nut castellations. The perpendicular surface of the ring looks straight and even, though a bit more compressed at 7 maybe. The grease on the outdrive/bellhousing surface didn't look washed at all. Almost easier with a big leak, right? Seems like a lot...
  10. nola mike

    Engine alignment ,just got the tool. Pics posted

    yes. Adjust fore/aft and see what happens. There isn't a port/sbd adjustment. Check rear mounts to make sure they aren't collapsed. Possible that one side is higher than another, but short of suspending motor with front mounts disconnected, I don't think you can check that. I chased port/sbd...
  11. nola mike

    MerCruiser 5.0 MPI pinging/detonation at higher RPMs

    Is there no knock sensor? Have you tried swapping injectors and/or plugs to a different cylinder? Have you eye balled the flow from the injectors or put a noid light on them?
  12. nola mike

    Bah. Water in bellows.

    Just pulled my drive today. Plan was to swap lowers (current one has too much play in the shift shoe). I had a small amount of water in the bellows. Not sure where it's coming from. Didn't have time to investigate much. Bellows are fairly new and good shape as of last summer. U joints and gimbal...
  13. nola mike

    MerCruiser 5.0 MPI pinging/detonation at higher RPMs

    At least you can buy a car with a stick shift...
  14. nola mike

    MerCruiser 5.0 MPI pinging/detonation at higher RPMs

    Wasn't meant to be snarky...a few people posted the same thing, and I didn't see how that could be the issue.
  15. nola mike

    Hole in Mercruiser gimbel housing

    My trim senders have only occasionally worked over the years. Never got around to actually reconnecting them after the engine swap 3 years ago. Pretty useless IMHO, at best a "while you're in there" job. Not to mention a huge pita on a gen 1
  16. nola mike

    MerCruiser 5.0 MPI pinging/detonation at higher RPMs

    How would a loose clamp down bolt lead to that upper wobble with the shaft not having play?
  17. nola mike

    Building a gantry crane

    Mine is still sitting in the driveway almost 3 years later. I'm afraid that if I dismantle it, my motor will immediately blow ;)
  18. nola mike

    Engine alignment ,just got the tool. Pics posted

    Agree with all of the above. Also, *very little* grease is needed on the end. It's more to see where the bar is rubbing than to actually lubricate anything.
  19. nola mike

    Oil Change Vacuum Merc Adapters

    That'll make it *much* slower though. You're reducing the diameter of the tube by quite a bit.
  20. nola mike

    mercruiser 188 fuel help

    I think we're talking about a Ford V8? Op has some trouble shooting to do. As far as turning over slow, you want to clean up your wiring between the starter and battery and the grounds, if that happened before the overheat. Is the engine turning over? Do you have spark? You can get an overheat...
Top