Search results

  1. R

    Lady's Johnson 15 Outboard Cylinder Head Repair

    i found nice movie.Lady is fixing outboard http://www.youtube.com/watch?v=MkL2HIGRcaU
  2. R

    runing cold Evinrude 15hp 96'

    hi. i got nice motor, but i dont know any fact from history. i run this motor few hours, usualy at low speed. i notic oily spots flating around transom.sure i use 1:50 mix with tcw3 oil. this spots looks like i put some fuel around. after runing at low speed motor starts usualy with choke on...
  3. R

    Johnson 15 HP, 79' rebuilt

    hi. in my progres in rebuilt Johnson 15 hp, 79' i'd like to shear some info. i did powerhead repair(head flatened 0.3 mm, cylinder surface flatened 0.4mm). new rings instaled, new upper and lower sealant,head gasket thicknes added 0.4mm. instaled mikuni fuel pump. new termostat. first run at...
  4. R

    rings question

    Hi. i'm going to order rings for my new 79' 15hp. i found rings on boats.net- omc 0386279. from description i see this set contain 4 rings-1set require.am I corect?
  5. R

    9.9/15 head bolt-extra problems

    hi. i run in notexpected problems. friend gave me to fix his 15 Johnson,79'. the problem was water circulation problems. he burn paint on the head area-head become brown(should be white) head was blocked with sand, termostat full of sand, termostat stuck closed ,no water circulation so i started...
  6. R

    slow speed needle adjustment-9.9 Johnson 83'

    hi all. last year i rebuild carb in my motor. put needle seat(nylon) in slow spped circuit, new oring on needle. motor runs good, start to adjust slow speed in 1.5 turn out but when i try to adjust slow speed needle i just turn in the needle, wait few second and turn in more but and motor is...
  7. R

    clearance in rebore cylindef for oversize pistons/rings(gap between piston cylinder)

    i had to put oversize pistons and rings in my 4.5hp Evinrude 80'. the repair shop will rebore cylinders but the guy asked about clearance between piston and cylinder wall. how much it should be.piston while working will expand some dimension, so how much cylinder shoud be wider.and clearence...
  8. R

    Evinrude 35 hp some words?

    hi. i'm looking for opinion about this motor MODEL;359862A SERIAL:7289
  9. R

    4.5hp Evinrude 1980 after rings replacement

    hi. i put new rings(standard) in my motor 4.5 Evinrude 1980. after rings replacement oiled cylinder inside. motor run 2 hours, with water cooling(garden hose),lost compresion.start only with chocke out. I decided to take apart powerhead once again. inside cylinder bore i could see some smal...
  10. R

    piston orientation 4.5hp Evinrude 1980

    i did the carb job, took out pistons, but i didnt pay atention which side should i put them back. isnside piston are 2 marks( mark looks like arrowhead, and letter "L") so "L" means low, and this side down?
  11. R

    Needle bearing question

    hI. I refer to needle bearing at drawing http://www.boats.net/parts/search/BRP/EVINRUDE/1980/E5RLCSS%201980/CRANKSHAFT%20%26%20PISTON-4.5/parts.html part no, 11, 15 during decarb i lost one or two needles from bearing no 15. is it posible to find out how many needles should be in this bearing...
  12. R

    spark plugs for Evinrude 15 hp 1997

    hi. My friend just owned motor as described in title, rope start, 2 stroke. we just looked at parts catalog and for this motor is mentioned 4 types of spark plugs. which one shoud i order? Best to you
  13. R

    oversize rings

    Hi. i'd like to ask once again about rings. if id like to instal set oversize rings-0.02"(0.5 mm) or 0.03"(0.7mm). do i need also to buy new pistons for this oversize rings? i know i should rebore cylinders to fit this oversize rings.
  14. R

    REPLECE NEEDLE BEARING TO BRONZE RODE BEARING ni Evinrude 4.5hp 1980

    Hi. i bought very cheap motor.i'm trying to rebuilt it. the problem is needle bearings. i took apart powerhead and found needle bearings warm up. i cant get new one(center bearing especialy), and mostly bearings are expensive. i know the auto repair work shop and they told me to replase needle...
  15. R

    interchange head in 9.9

    Hi. i'm thinking if its posible to change old type of head on 9.9 1983y(termostat in the lower part of head) with the newer one (termostat in upper part)? will it work fine?
  16. R

    9.9 termostat(1983)

    hi. In the past i changed termostat in my motor. i put new termostat and all staf(spring, cap, rubber bushing, gasket) i just but it back as it was mounted before. im thinking if this spring is nesesery? while puting back terostat cover i had to keep this very careful and tight, becouse spring...
  17. R

    johnson 9.9 83' powder painting

    hi. in last week i did powder painting with my motor. first i had to reasemble midsection, lower cowl and powerhead(except lower unit is not painted), next step was to send all aluminium parts after cleaning i gave this parts to painting workshop to cover them with paint powder and put them in...
  18. R

    johnson 9,9_83 powerhead bolts

    i tear down powerhad. thera are 6 bolts holdind powerhad to mid section.2 of them are longer. i'm not sure, but this longer one should go to this side where head is mounted(under of courese)? meybe some one remember wher this longer one goes?
  19. R

    Needle float clip in johnson/Evinrude 9.9-83y

    hi. in last week doing my fishing trip i noticed strange symptopms, usualy at troling speed.engin vibrates more than usualy and sometines cuffs nad just died.it looks as engin gets too much fuel. i try to adjust slow speed needle but it didnt help, check spark plug wire and sparks.but seems to...
  20. R

    9.9 convertion from short to long shaft(83y)

    hi.i'm trying to convert my 9.9. i have lon drive shaft and 5" extension.i want to use my lower unit, but i dont kwow how to take out my short sfit rod from lower unit to place in shift rod for long shaft.Or maybe i do need a new lower unit with mounted in longer shift rod? i read LeRoy wisner...
Top