Search results

  1. Horigan

    quick question on shift cable setting volvo sx

    Which ever way prevents you from turning the prop in reverse is forward.
  2. Horigan

    Dust Cap Woes

    I’ve used the old races to get the new ones in.
  3. Horigan

    Volvo Penta overheating

    First I would backflush the cooling system and find all the missing impeller blades. They are likely clogging key parts of your cooling system. If you're raw water cooled, this would include pulling the thermostat in the flushing process.
  4. Horigan

    Zinc contact points- sand clean?

    I've read that wire brushing is not good for a sacrificial anode as it imparts some steel onto the surface reducing its effectiveness. Rough sandpaper is what I use.
  5. Horigan

    Zinc contact points- sand clean?

    I sand the small raised contact area around bolt holes to improve conductivity to the drive/transom. Yes the bolts provide most of the connection.
  6. Horigan

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    Older radios typically receive GPS data via a NMEA 0183 cable (or NMEA 2000 for newer radios) with data coming from a GPS antennae. The function is to enable the distress button to transmit your coordinates.
  7. Horigan

    Bearing Buddy dust cap "bra" coming off 1 hub while trailering

    Zip tie?
  8. Horigan

    Vinyl protectant/conditioner

    I've been happy with Starbrite Vinyl Cleaner & Polish. It has UV protection.
  9. Horigan

    Wiper Arms

    Soak with penetrating oil for a few days.
  10. Horigan

    2nd battery needed if installing prawn puller??

    The numbers say the single battery would work. I would assume 30A for this calculation (I sometimes blow the 30A fuse pulling pots) so you'll pull up to 10 Ah (amp hours) in 20 minutes from the battery, without idling.
  11. Horigan

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    Once you're able to get the drive fully down, adjust (rotate) the sender until the gauge reads fully down. My gauge tends to show more movement near down than when trimmed up for trailering.
  12. Horigan

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    The pump squealing you hear at the trim limits is normal. It is the pump flow going through the pressure relief valves within the pump. The drive you have is a Cobra SX, and a Volvo SX-M. Same component part numbers. I use this site for parts diagrams...
  13. Horigan

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    Your props are same diameter, 14.5. The new one has a lower pitch, 19, basically like a lower gear. So you'll have better hole shot, but you may over-rev the engine at max throttle. Watch for that as you work up to max throttle.
  14. Horigan

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    If the O-rings are about an inch (3 cm) in diameter, they go on the grooves on the input shaft. Lube with motor oil. There should be three additional smaller O-rings. Two for the drain hole and the middle hole plugs, and a slightly larger one for the dipstick. You must fill the leg from the...
  15. Horigan

    1996 Four Winns Sundowner with 5.0 Cobra engine and drive

    ...
  16. Horigan

    Jerry-Buddy?

    Then there's the mess when you need to refill the tank. Pull the drippy hose and check valve out and set it somewhere while you fill the tank.
  17. Horigan

    Seeking Guidance - Penta SX-A Cone Clutch & Cable Issue

    One thing I’ve done to reduce the slop in the mechanism is to add additional washers or a zip tie to eliminate the lateral movement. If there is slip, this will help to reduce it and provide more cable travel.
  18. Horigan

    Volvo Tilt/Trim Sensor

    It's a pain to get to depending on the motor configuration. When installing the new one, put some synthetic grease on the rubber part of the sender so it goes in fully into the hull. More fun than removing the cotter pin is putting it back on to the new one.
  19. Horigan

    Winch replacement suggestions

    Actually, the concern would be the amount of strain energy. So the cable would brake with little spring back of the failed end. The nylon strap would spring back with much more velocity.
  20. Horigan

    Grease tube on VP DP-SM, fitting striped

    Newer gimbal bearings don't require greasing and don't have a grease port. So another option would be to install a newer bearing and seal the grease fitting port somehow. Being full of grease may be sufficient.
Top