Search results

  1. Faztbullet

    1986 Johnson 175 missing

    #2 coil cold have a problem, also index flywheel and check timing as flywheel magnets where a problem these year models. Something is causing the CDI junktronics fire the cylinder late and it could be the CDI replacement parts
  2. Faztbullet

    This carb gasket doesn't look right?

    +1
  3. Faztbullet

    early 70s Mercury 500 50hp ignition question

    What makes you think coil is bad as those rarely fail???? Never was a belt driven distributer model with individual coils either all where single coil..orange,red ,green or black
  4. Faztbullet

    Trying to figure out carbs on a 1993 120 looper

    Depending on carb series and shaft length Intermediate is always a few sizes smaller than idle. You need to flip your jets if 30 is in the bottom
  5. Faztbullet

    piston to cyl head clearance... 3 cyl looper

    Put gasket on it and go. Might have raised compression 2-4 psi. If under .020 oversize go up maybe .001 on main
  6. Faztbullet

    1987 mercury 60 hp piston damage

    "Thanks for the response, does this breakdown happen over time or does it happen pretty quickly" If timing is a tad high it will happen slowly but gradually build up faster as the erosion takes place. A Racer said these do have a overheat problem but piston shows no other signs leading to a...
  7. Faztbullet

    1987 mercury 60 hp piston damage

    That be preignition from improper timing or bad bais in switchbox. When we raced Inlines we would jack timing to till we started getting erosion(throwoff) and then back it down a tad, plus we wuz running avgas
  8. Faztbullet

    Electric prop rotation

    It has the wrong prop on it or installed wrong. All Minnkotas turn CC for forward motion.
  9. Faztbullet

    The Joy Stick.-

    That top plate is a SPLASH DEFLECTOR and that is its only purpose!!! It has no bearing on where motor height should be!! Here is mounting for Yammy 30 from the manual..
  10. Faztbullet

    Any HiPo guys???

    Got a customer with twin 575HP Mercruisers with new XR drives. Problem is after running and setting motors are vapor locked. Fuel rails have no shrader valves I can find. Thinking about drilling rails, installing nitrous solenoids and dumping into a catch can that will drain back to fuel system...
  11. Faztbullet

    Aftermarket Parts

    Cause: The cause of dowel pin migration in these cases is not a defective piston, but a lack of water (coolant) in particular areas of the block, resulting in elevated temperatures in the cylinder/ piston.
  12. Faztbullet

    Mercury 115HP 2 stroke 4 cyl Carbs.

    Here ya go..its in the PM also...
  13. Faztbullet

    Crankshaft Journal Wear

    Crank needs replaced along with rod and all pistons besides the one that failed. This is a cooling issue with block that causes locating pin to migrate out. If one has failed the other are loose and will soon follow. Need cooling mod installed to block..
  14. Faztbullet

    1998 Johnson 225 Rebuild

    Well 1st off you need to check the plastic restrictors/deflectors in port/starboard cylinders. Also replace ALL pistons as if one pin has come loose the others will follow soon. (Use cast pistons!!!!) This is a cooling issue design problem and is mandatory that you change impeller every 2 year...
  15. Faztbullet

    XR or X drive???

    Got a friend with Baja with XR drives...he chit one over weekend and I have found driveshaft and propshaft splines twisted on the other. Has anyone used the X drive replacement as these dogs aint cheap to repair or replace!!!
  16. Faztbullet

    Any Westerbreke techs on iBoats?????

    Got a Westerbeke 22.5 sbeg EFI kicking my butt. Wont start unless a shot of starting fluid is applied. All sensors check/ohm out, fuel pressure 40psi, injector firing(noid) when cranking just not getting bump off and sometime starter just hits for a second like it lost a connection. I have...
  17. Faztbullet

    Prop pitch suggestion for 2019 Yamaha vmax 90 sho

    Lets just say Qboy you wouldn't like riding with me !!!!!! When in Doubt – Trim it Out
  18. Faztbullet

    Prop pitch???

    The project boat launched today!!!! Anybody want to guess my prop pitch????I know it already.... Boat; 12' x 60' Motors: 2 x 225 Merc 25"length Cavitation plate: 1.9 ft off bottom of hull( that is feet!!!) Weight: 56,000+ plus below 4 passengers,100 gallon fuel, 4' x12' roll off box, 1 Terex...
  19. Faztbullet

    Thoughts on Firs Time Starting A Dormant V4 with new Wiseco Pistons

    I have a hand built moderately tuned V4 that has not been started since having new wiseco pistons and tuned in early 2018 Any thoughts on breakin and starting for the first time. Edit Start it up and let it idle( 4 hrs ) just like it says to do on the fact sheet.------You did bore and hone to...
  20. Faztbullet

    1994 evinrude 175 stalling and tach issues

    #2
Top