Search results

  1. alldodge

    not getting fuel

    Being a carb motor I'm going to assume its a GL, but a GL what? The GL uses feed from the Key switch (yellow/Red) to energize the start assist relay and the fuel pump relay. The feed to energize the FP relay goes thru a diode. If the diode opens then the relay is not energized. Once the...
  2. alldodge

    Cabin heater core blowing cold air.

    OK, I understand better, the issue is showing open cooling system and talking closed and heaters For coolant to circulate thru a heater it needs to go from a higher pressure area to a lower pressure area. The low side needs to be on the circulating water pump (left side facing motor) or Tee'd...
  3. alldodge

    Chrysler 125 removal

    Got it out
  4. alldodge

    Cabin heater core blowing cold air.

    Your motor will over heat if the red one is plugged. This is the flow of fresh water from the drive The ones in white would go the the exhaust manifolds If your trying to install a HE on the motor, lets start with, what motor, what year and serial numbers are best
  5. alldodge

    1993 OMC Cobra 351 EFI Ford 5.8 how to start?

    Don't know if the wires will fit, don't know what motor they are for. Do know that marine wires need to be longer because they go under the manifold instead of over Take the hose that would come from the outdrive going to the thermostat housing and connect the garden to it. The pic below are...
  6. alldodge

    7.4L MPI (L29) MEFI 2 Fuel Pressure issue

    This is what they look like
  7. alldodge

    1993 OMC Cobra 351 EFI Ford 5.8 how to start?

    Using a sander will make it look nice but will not be flat. If it was put on a lathe this would work, otherwise would need a flat file but that would take a long time Wiring
  8. alldodge

    Guardian Mode Alarm Help

    The key is max rpm exceeded On the shift plate is a "in gear" switch, and if the PCM things its in neutral then when 3200 rpm is exceeded it throws the error and alarm Unplug the switch and see if that fixes it
  9. alldodge

    Alt Gauge Help

    Here is the GL-E wiring
  10. alldodge

    Chrysler 125 removal

    Question is did I get them all? Think I got all the fastener's (11 total) off and think its just the silicone holding but want to make sure There are 2 nuts on right rear and 3 nuts on left rear side There are 6 bolts on the top plate There are 2 other bolts which I have not removed and there...
  11. alldodge

    Engine Hesitation/Fuel Issue - 1995 Crownline BR202

    Howdy Sounds like its the tank vent line The fuel tank must be vented, otherwise as the fuel is pumped out the tank starts to draw a vacuum. With it taking 60 to 90 minutes to do this, is a real sign that is most likely the problem To prove it out, when motor starts to bog, stop and open the...
  12. alldodge

    Chrysler 125 removal

    Thanks Jerry, this is what I was thinking, but some of them are so tight I was thinking about removing some of the linkage and brackets to get at it Makes me wonder just how were these built on the factory floor.
  13. alldodge

    1994 5.7 liter won't start

    Your serial number is coming up as a carb, not understanding the term "manifold" with reference? I'm seeing TBV ignition. I know you said there is good spark but have you tied the TBV trouble shooting guide
  14. alldodge

    Chrysler 125 removal

    Should be simpler then I'm seeing. What bolts are removed to lift motor off the leg?
  15. alldodge

    Wiring help needed 4.3L TB-IV

    Do this to start and run
  16. alldodge

    2002 Tahoe 202 - Mercruiser 5.0 MPI fuel pump not priming

    There are 2 other connections
  17. alldodge

    Outdrive wont go back on!!!!!!

    It goes in and out with 2 fingers and drive will not go on, I would say there is something wrong with your alignment tool If different spacers are needed, then need to look close at the rear mounts, they may need replacing Was the gimbal bearing replaced, and if so are you centering it...
  18. alldodge

    Not Turning Over, Low Compression, Mercruiser 3.0

    How to start
  19. alldodge

    SC1000 Smartcraft gauge can't read digital readout

    Boat yard installed motor and gauges, so why doesn't the boat yard fix the issue, or have you asked? If the tank is not connected to the CAN network then it doesn't know. If it is connected, then once programed, and gass is added, it will calculate how much is left based on the level Is your...
  20. alldodge

    2002 Tahoe 202 - Mercruiser 5.0 MPI fuel pump not priming

    The MPR sends power to 2 other fuse, one of which is for the FPR. When MPR connects there should be 12V on pin 85 and 30 (not 86) on FPR along with connection to the IAC. So there is a bad connection or MPR coluod be the issue
Top