Search results

  1. Ifishmuskie2

    Aluminum Boat Paint

    I’ve had good luck with brushed on tremclad.
  2. Ifishmuskie2

    Play in steering then found this..

    What was it like when you had it on the water? I have outboards but they seem loose ( too easy to flop around) when on land but in the water they are good.
  3. Ifishmuskie2

    Honda BF20HP maximum revs

    All I can tell you is I’ve run a three blade aluminum 11 pitch vs a SS 11 pitch and the SS was way better. (3mph top speed and hole shot). On a 1200lb total weight aluminum and it goes 25mph.
  4. Ifishmuskie2

    What Is this alarm? Mercury 2001 125hp

    One of the reasons I want to keep my oil injection is because it does a different mix ratio for different rpm.
  5. Ifishmuskie2

    What Is this alarm? Mercury 2001 125hp

    My oil injection system seams to be very good. Very little smoke. Quick silver oil. Part of the reason I have a side console boat is so the windshield and Bimini doesn’t trap exhaust. My tank is about 12” tall and holds 5.3l. I did a 30mile trip and I used about 1.25” of oil. A big day of...
  6. Ifishmuskie2

    What Is this alarm? Mercury 2001 125hp

    My 115 mariner has a connection block where the high temp wire and low oil wires (reads low oil only not flow)are connected together (lower starboard on engine block) and then a wire into the wiring harness up to the dash. My alarm was going off steady so I disconnected the low oil warning and...
  7. Ifishmuskie2

    View of unloaded trailer with pickups

    I was waiting in the water at the ramp for the two guys ahead of me to pull their jet ski. The owner told his friend to back the trailer down. Well he got everything straight and started backing. He was using his mirrors and couldn’t see the trailer so everything was good. A few feet later...
  8. Ifishmuskie2

    Trim gauge not working

    The sender isn’t connected to the bolt with the slot in it. Possibly the wrong sender. The gauge moves when i turn the sender by hand. I’ll modify the sender to allow it to stick out farther and into the slot in the bolt.
  9. Ifishmuskie2

    Trim gauge not working

    It’s possible that it never worked. Whoever installed it didn’t hook up the backlight. I’ll have to check the sender tomorrow. Thank you.
  10. Ifishmuskie2

    Trim gauge not working

    The gauge moves to full up when I turn the key on.
  11. Ifishmuskie2

    Trim gauge not working

    I get 48 ohms then 42 as I press the tilt up so the sender wire is changing resistance.
  12. Ifishmuskie2

    Trim gauge not working

    I have difficulty getting the engine trimmed to the sweet spot. It doesn’t have a trim pin. Maybe I’ll get a trim pin and put it on the sweet spot. The engine has lots of power so I don’t need to adjust trim after I find the sweet spot. It’s on a 1994 StarCraft walleye 180. (Super fisherman)
  13. Ifishmuskie2

    Trim gauge not working

    115 mariner
  14. Ifishmuskie2

    Trim gauge not working

    I worked at the spaghetti factory (wiring) all day. I got most of it done. Trim gauge is not working. The trim gauge might not be original. there is no wire for the light and I can tell it never had a wire hooked to it. the hole is cut out different from the rest. Gauge is out of boat and...
  15. Ifishmuskie2

    Anchoring a Starcraft Islander 191V

    High gunnel StarCraft are like having a sail out. If there’s very little wind you could put two small anchors off the back corners.
  16. Ifishmuskie2

    1994 StarCraft walleye 180

    I have a 1994 StarCraft walleye 180. It’s 18’9” overall length and 7’4” wide. Does anyone know the fuel tank size?
  17. Ifishmuskie2

    1994 mariner 115, oil injection

    It has a SS five blade prop but I can’t find any numbers on it.
  18. Ifishmuskie2

    1994 mariner 115, oil injection

    About 5200rpm. These are low rpm red line engines.
  19. Ifishmuskie2

    1994 mariner 115, oil injection

    Before I ran it I replaced the thermostat and impeller and it’s got lots of cool water coming out the pee hole. No signs of overheating on the head. I ran it for the third time yesterday. Went about 30miles. It pushes the boat nicely so I’m cruising between 3000-4000rpm. 20to30mph. Wot is...
  20. Ifishmuskie2

    1994 mariner 115, oil injection

    I was able to get out today and no oil leak. I only tilted up as far as I needed to not all the way and the oil tank is only half full. I marked the tank before I went out and I used 1” of oil which seems about right. I’ll just keep an eye on it. Nice boat ride with the wife.
Top