Search results

  1. P

    My 84 4winns horizon 195 project.

    Made some more progress. There are some air bubbles on the outer stringers but given the original ones were only tabbed in on one side, I think I'm fine. It's already more structural than the original. I also picked up the fuel tank. Only thing I'm nervous about is while the vent is on the...
  2. P

    My 84 4winns horizon 195 project.

    Just got word my fuel tank is ready for pickup. I know what I'm doing Monday.
  3. P

    What gives with helping people with a problem ?????????????

    I never closed out one of my threads but in my defense, it was documented that I had to rebuild and that it's been fine since. My favorite is on another forum, the old "I fixed it no help to you all" and I chuckle because most of the time, when someone feels the need to post that response they...
  4. P

    Assembling a 4.3 MerCruiser v6 - Parts check needed

    I've slapped together some junk but that's rough... I'd probably bail if they are offering....
  5. P

    My 84 4winns horizon 195 project.

    I agree. Though I was shocked at how close everything was when i measured it all. Guess it was a Wednesday boat. :ROFLMAO:
  6. P

    My 84 4winns horizon 195 project.

    This felt like progress... I got the outer stringers bedded in and added a half layer of glass on the transom and continued grinding the hull. Some more minor cutting and I'll be over the hump so to speak. I am still gassed from the weekend so I doubt I will do much tomorrow. Maybe I get the...
  7. P

    Assembling a 4.3 MerCruiser v6 - Parts check needed

    Yes. I used an ebay kit and flipped the choke arm in my vise instead as it was quite a bit cheaper at the time. There is a hole you have to drill for the internal pull off.
  8. P

    Assembling a 4.3 MerCruiser v6 - Parts check needed

    I think some may have? The one I inherited came off a 94 and the choke linkages were set up like it had the heated stove pipe choke and it had the external vacuum pull off... I drilled the carb for a later edelbrock style electric choke and ditched the pull off. It does bolt to the 2519...
  9. P

    My 84 4winns horizon 195 project.

    In case anyone was wondering, I found the problem. :ROFLMAO: Lost a lot of time this weekend. Had a call for a MVA accident Friday that ate most of the day up and power is still out to the best of my knowledge... thats a big setback. Hopefully I get some good time in Wednesday.
  10. P

    My 84 4winns horizon 195 project.

    Worked on the grinding some more. Templated the outside stringer... tree knocked out the power so I'm early done for the day... was hoping to get the outside stringers in but it can wait. I also glued the first main stringer.
  11. P

    My 84 4winns horizon 195 project.

    Did a lot of grinding yesterday. Hoping to start getting stringers in today. I also want to template the false floor. My idea is... glass in the stringers then make the false floor one continuous board from the engine box to the bow. Then glass the bulk heads on top of that. It seems the bulk...
  12. P

    Easiest Conversion

    The bare minimum stringer width needed for a 4.3 or 5.7 from merc is 24 inches if I remember right from my swap. Realistically 26 would be better as it's very tight at 24... I used every inch of it.
  13. P

    Assembling a 4.3 MerCruiser v6 - Parts check needed

    That is more or less where I plan to start with my calibration as well. And from what I recall it is pretty close to the mercruiser calibration for the vortec engines.
  14. P

    My 84 4winns horizon 195 project.

    It is ideal. The plastic is rather thin but hey... it works and keeps everything warm. I have a 5k plug in heater and its at temp in 20 minutes. And thank you. I keep getting worried I didn't roll it enough or I should've used the fin roller more but I didn't saturate it and just used enough...
  15. P

    Assembling a 4.3 MerCruiser v6 - Parts check needed

    The edelbrock calibration kit for the V6 is reported wrong by many on here. Calibrate it to service manual 18 or do a search around. The non vortec calibration is close if memory serves but the vortec intake and calibration is way off. You either have a weber or quadrajet. Most likely a weber...
  16. P

    My 84 4winns horizon 195 project.

    Started scarfing the wood together yesterday. I'm doing an 8:1 on the small outside stringers and a 12:1 on the main center stringers. So far so good.
  17. P

    anybody need a good used prop shaft??????????????

    I've got one like that in the tool box too. Get a chuckle every time I see it. Some customer of dads from before I was born.
  18. P

    Assembling a 4.3 MerCruiser v6 - Parts check needed

    FYI, the cast iron 4V vortec bolt pattern intakes exist online for around $300. Little cheaper than the edelbrock unit. Then you just need to jet your carb per the service manual. (If its the 4 barrel unit) The distributor gear is a typical small block gear, you want a melonized one.
  19. P

    My 84 4winns horizon 195 project.

    So I ended up tabbing in with 2 layers of 1708. One layer of 1708 on the entire transom and tied with a topping of CSM. I think that is more than enough for this.
  20. P

    Restoring 1988 19’ bayliner capri

    The 435 non waxed I am using from US composites dries tack free after a few hours as well... Quick dab of acetone brings it right back though. Seems like if it is warm enough, it'll dry tack free. I am keeping the garage around 85 degrees while working so layup times are reasonable.
Top