Search results

  1. jerryjerry05

    Identifying Chrysler 45 hp Outboard year and Model Number

    Someplace on the block is a foundry stamp. The stamp could be round with the year in the middle of the stamp. Most times its on the stbd. side or possibly under the carb on the intake manifold.
  2. jerryjerry05

    Fresh bore and 125 psi on one cylinder??

    Yes, bigger jets.
  3. jerryjerry05

    Mercury force 120

    Year??? Model???? Add pics(any photo sharing site) of your lower or where the parts missing? After 5posts you can add photos. Without the year it can have different linkages.
  4. jerryjerry05

    repair mishap

    outboardignition.com has tests for your system. A stator or trigger even rectifier can look good but bad inside. A stator can test good and still be bad :(
  5. jerryjerry05

    1989 ish Mercury Force 120 ignition issues

    The gaskets should be thick and stiff with a sealer already on them. The factory used no sealer just good gaskets. The mounting surfaces might need a mill job. Over time the heat causes them to round off and makes resealing tough. Usually when I do a rebuild and if there is no problem with...
  6. jerryjerry05

    Fresh bore and 125 psi on one cylinder??

    125 isn't great. Maybe the gasket didn't seal right. At .040 over you might need to reject the carbs??? Remove the head, add a little gasket sealer around that hole then do the comp test again. If this makes the difference then the surfaces might need squareing off??
  7. jerryjerry05

    Force 85 1987 bayliner capri

    Set the idle up. The towershaft , towards the bottom is a slotted screw and a 7/16 nut. Unhook the linkage. Loosen the nut and turn the screw in. This increases the rpms. It kinda sounds like it's sucking air???? Start the motor, can of starting fluid, spray the fluid around the intake side of...
  8. jerryjerry05

    Remote control help

    Need model# serial# pics of the shifter and the linkage on the motor
  9. jerryjerry05

    1983 60 hp Evinrude shift rod height???

    Thank you!!!
  10. jerryjerry05

    1983 60 hp Evinrude shift rod height???

    60 hp 1983 need the shift rod height?????The shaft is 20-21" Somebody just beat the shift mechanism to death and I had to replace it. THANKS Went to the site where this info is usually listed(Top Secret File), every time I try to open it, it goes to a post about a Chrysler motor and if they...
  11. jerryjerry05

    1996 Force 90hp flywheel

    Research, LOTS of research!!! :)
  12. jerryjerry05

    1979 Chrysler 140 (1409H9B) barn find. Looking for help!

    The fill/vent PLUG, GEAR HOUSING F50109 are the same as the older Mercury ones. Use a washer also Mercury The plastic "crush" washers were fairly good but were a one time use only. The Mercury could be used again and again. WASHER, GEAR HOUSING PLUG F8077 Not sure what the...
  13. jerryjerry05

    1989 ish Mercury Force 120 ignition issues

    Just buy the black and us solder to connect the cut off ends. I've seen NO difference in the Blue and Black When they started making the black they changed the connectors so you'd have to buy black coils.
  14. jerryjerry05

    Erratic Timing Light Reading on '96 Force 120

    Hey mod!! Maybe put a link to this in the stickies ???? THANKS!!
  15. jerryjerry05

    Erratic Timing Light Reading on '96 Force 120

    The 96 120 used the Mercury ignition. Find the steps for setting the Mercury ignition.
  16. jerryjerry05

    Carburetor float question

    Yup they are right on the first 2 and the 3rd is off a little too. The float should be even not raised a little
  17. jerryjerry05

    1996 Force 90hp flywheel

    All the "old" guys usually pass on. FrankA, Don, RRitt and a few dozen more left with an immeasurable amount of knowledge when they went to the big boat repair shop in the sky. :(
  18. jerryjerry05

    1989 ish Mercury Force 120 ignition issues

    Standard Magneto and Ebay is cheaper. http://standardmagneto.com/marine.html Standard is "NEW" listed about 72-82$ US.
  19. jerryjerry05

    1996 Force 90hp flywheel

    This list is from boats.net it covers everything that the flywheel fits. eBay has one listed that might fit??? https://www.ebay.com/itm/125436399198?hash=item1d34978e5e:g:PvYAAOSwm55i4gQp Mercury Sportjet Jet Drive 120HP 120XR Sportjet Jet Drive 0E145580 THRU 0E151579 Electrical Components...
  20. jerryjerry05

    1989 ish Mercury Force 120 ignition issues

    Little drops of water on the plugs??? NO WAY should there be ANY water in the combustion chamber, any at all. Water on the plugs show the head gaskets probably bad or not sealing??? Had a 88/85 that started missing, did a comp test and 145 all 3 cylinders. Then I noticed 1 tiny drop of water on...
Top