Search results

  1. T

    1974 Evinrude 25hp wont run.

    I agree No one is forced to answer your questions and if someone has had enough they are free to jump off the train at any time. Best
  2. T

    1974 Evinrude 25hp wont run.

    I would shoot for 650 to 700 rpms while in gear and not tied to the dock. But that just me.
  3. T

    1973 johnson 25hp 25R73A

    Roadking Using the old head gasket could be a problem. Once they are compressed is usually game over. Just a thought.
  4. T

    1991 evinrude outboard is this normal?

    I’m in agreement with all of the above. Let it run for awhile and get up to operating temp before worrying about it to much. Everything may just work it’s self out fine.
  5. T

    1973 johnson 25hp 25R73A

    Welcome home. You you had a Blast.
  6. T

    Does this gear and clutch dog look ok?

    Not looking all that great in my eyes.
  7. T

    1970 25hp deceleration after run at WOT

    No need to worry about timing marks. You are correct the light will stop blinking if you drop a cylinder. It sounds like you carb was in need of a good cleaning and you may find that’s what the problem was. Best
  8. T

    1974 Evinrude 25hp wont run.

    The mag plate is moving back and forth because the coil is to close. The flywheel magnets are dragging the mag plate. It doesn’t need to be physically touching to be to close if that makes sense. As stated line in up with parallel with the flats on the mag plate.
  9. T

    Gear case hole?

    It that a crack above the drain screw ?
  10. T

    1970 4 hp Evinrude stops suddenly

    I’m sorry but it drives me crazy when people bash Chinese quality. The ones to blame are the companies that spec their products to be made. If you spec a quality product that’s what you will get but it comes at a higher price and that’s when things go down hill. I have spent some time in China...
  11. T

    Evinrude Mate 2 HP Driveshaft

    Great news. If by chance it doesn’t work out. There is a difference between welding and spray welding. Spray welding is considered a cold process and should not warp the shaft. Hopefully the polishing will work out for you. Best
  12. T

    1974 Evinrude 25hp wont run.

    I’m leaning towards your coils not being adjusted correctly. They are likely dragging on the flywheel.
  13. T

    1989 Evinrude 30 2-stroke losing power at high RPMs

    I could be wrong but I have seen a few that look like that. I believe there made by Atwood.
  14. T

    1989 Evinrude 30 2-stroke losing power at high RPMs

    That supposed to be the tank vent and it’s broken. You need to vent the tank or it will leak when it expands and it will keep your motor from running as well if its closed. I only close mine durning transport in my truck. You should get a new tank or at least replace the sending unit.
  15. T

    2010 Evinrude E-Tec 60 HP cold start up issues

    I had this problem once and when I took the starter apart I found a cracked magnet. It would be worth disassembling to have a look.
  16. T

    64 Johnson 9.5 “Turtle Motor”

    If I’m understanding this correctly it sounds like you have to much water in the barrel. Maybe even covering your exhaust so you may be pumping water just fine but you can’t see it.
  17. T

    64 Johnson 9.5 “Turtle Motor”

    Are you sure your water tubes were lined up on reassembly?
  18. T

    Evinrude Mate 2 HP Driveshaft

    It could be spray welded and turned back down to spec if you can find a good machine shop.
  19. T

    Help me find the missing piece

    Looks like your shift and throttle cables are missing the hold down.
  20. T

    No pee Johnson outboard

    Premix Fuel in a spray bottle is a good alternative to starting fluid. Just a little bit will wonders. I hope everything works out for you.
View older results
Top