Search results

  1. Scott06

    Alpha One Gen 2 prop shaft seal replacement

    Yes I can thread pipe just put an npt thread on it to grab the inside of seal ? Could weld a nut in other end to make a jack screw
  2. Scott06

    Alpha One Gen 2 prop shaft seal replacement

    Will give it a try before pulling carrier. thanks
  3. Scott06

    what do you see wrong with this picture?

    Don’t know never had one. Would assume they would drain out like max when changing. There must be some way to not make a complete mess
  4. Scott06

    Water on top of Intake Manifold

    check the oil for water if you think the intake gaskets are leaking. Possible it came down from the hatch cover depending on design .
  5. Scott06

    what do you see wrong with this picture?

    That is a remote oil filter pretty common on mercs. The fuel/water separator is usually down on lower left front of engine the oil in the bilge may not be a big deal could come from corroded timing cover or from drive seal leaking into bellows and into the boat. What would worry me is the...
  6. Scott06

    Alpha One Gen 2 prop shaft seal replacement

    I was going to make or modify jaws on one of the pullers we have at work. Not sure if I can make my own tool to remove the nut that holds the bearing carrier in or buy one (dont think they were too much$$). Luckily I have access to the shop at work ...
  7. Scott06

    2016 Mercruiser 4.3 TKS (Carb) Winterization Procedure

    No I have the five point drain, just no need to put the plugs back in the manifolds unless you fill the block up and it starts filling the manifolds when thermo housing overflows. Yes you can leave the AF in for corrosion protection. A lot of saltwater folks do this, but if you boat in fresh...
  8. Scott06

    Alpha One Gen 2 prop shaft seal replacement

    Bumping this didn’t know if there is a way to pull seals out with out pulling bearing retainer ?
  9. Scott06

    2016 Mercruiser 4.3 TKS (Carb) Winterization Procedure

    No need to use so much AF unless you get the good stuff which is PG based with corrosion inhibitors. I drain mine probe the holes, take the hose off thermostat housing coming from the drive pour about a half gallon that will back flush out the drive. Put the two block plugs and the J hose plug...
  10. Scott06

    Alpha One Gen 2 prop shaft seal replacement

    Went to take the boat out to winterize it yesterday (had not used it in 3 weeks) and noticed a oil sheen from the outdrive when I put it in the water... also noticed the lube bottle was down by about half, which I have never seen before. Take the prop of and predictably find a bunch of fishing...
  11. Scott06

    Alpha 1 Gen 2 Y-Pipe Flapper

    I think im getting the same thing. Looks like the original one piece units were superseded by what you bought. I came up with the part numbers below but i suspect it is what you have.
  12. Scott06

    Alpha 1 Gen 2 Y-Pipe Flapper

    Have a transom housing serial number ? Engine serial number
  13. Scott06

    89 Horizon 180 with stock 4.3 upgrade questions

    This is good advice. no sense going through it unless you upgrade significantly. You may be money ahead getting a vortec 4.3 from a wrecking yard and going that route. A good running engine 4 bbl intake and carb and you would be at 225 hp . I would keep the alpha one gen one drive vs going...
  14. Scott06

    2003 Mercruiser 4.3 TB-V No Spark

    SO with new sensor installed you strike green/white wire from module to ground and you get a spark off the coil? Or you only tried this with the ruler? if yes to striking the wire with new module I would agree that yes the new oem sensor is bad and try the next new one and see. Either way I...
  15. Scott06

    2003 Mercruiser 4.3 TB-V No Spark

    And is the black wire off sensor on a clean ground
  16. Scott06

    Tachometer bouncing

    You will need to remove it and helicoil or put a timesert or similar in there
  17. Scott06

    Floor issue 21' boat

    That's what you tell the wife ...
  18. Scott06

    Floor issue 21' boat

    If you have been there and done that before go for it. The concern of most posters here, not knowing your experience level, is that you know what this entails. Hopefully it is not too bad. Will be interested to see how much rot is there
  19. Scott06

    Solas stainless 4 blades all the same?

    So by lowest level you mean tabs are down more to push bow down? The engine rpm will bounce like that on the limiter as it drops spark to cylinders until rpms come down. If engine temp climbs at that rpm you need to look at the cooling system, if impeller has not been replaced I would do so...
  20. Scott06

    Floor issue 21' boat

    Given the obvious rot would want the guy to drill into stringers and transom. The water that rotted the floor had to go down somewhere... Like rust on an old car what you see is likely the tip of the iceberg.
Top