Search results

  1. C

    Fuel pump for 6hp 6904E

    blow which direction..?? install it with mounting bolts tight see was happens .
  2. C

    25hp Johnson won't start

    point must open at TDC ..something mecanical is needs a deep look into. did you change the condenser ..yes no ?
  3. C

    25hp Johnson won't start

    he replaced points and coils I am certain a missing or broken key would habe been noticed no ?
  4. C

    25hp Johnson won't start

    some points .. bad ones.... have appeared in recent years whereby the pivot arm rubbing on the cam lobe is not the proper length. There is no reason to have an off-set from the highest point of the lobe and TDC....reverify your points to ensure you are using the proper ones.
  5. C

    1993 Evinrude 30 HP tiller pull start

    classifiedst AOMCI may help
  6. C

    1977 Johnson 35 - Won't start

    https://www.bing.com/videos/search?q=utube++johnson+35hp+1977++no+start&&view=detail&mid=D107BA7FCDB7C395745DD107BA7FCDB7C395745D&&FORM=VRDGAR&ru=%2Fvideos%2Fsearch%3Fq%3Dutube%2520%2520johnson%252035hp%25201977%2520%2520no%2520start%26qs%3Dn%26form%3DQBVDMH%26%3D%2525eG%25C3%25A9rer%2520votre%25...
  7. C

    1977 Johnson 35 - Won't start

    https://i2.wp.com/www.maxrules.com/graphics/omc/wiring/77-78_55HP.jpg in the 55hp version the solenoid is locally grounded and the neutral switch is in series from the key'S START post. not much to stop 12v from reacing the solenoid control prost other rtan broken wires, fuse or defctive...
  8. C

    1977 Johnson 35 - Won't start

    Don't worry they told me I was color blind at my local Telco hiring office.. not good for splicing cable pairs..... so they kept me away from fixing color coded cables/pairs :) but I still worked 30 years there :) wiring is usuall y the least of problems :) but yes it can be a...
  9. C

    1977 Johnson 35 - Won't start

    ground wires are usually black power wires are usually red sometimes purple from the switch START post so don't apply power to black wires. you have to learn to use a volt ohm meter if you plan servicing your oldy post a color photo close up of your solenoid wires. but do easy...
  10. C

    1977 Johnson 35 - Won't start

    to test the solenoid " locally" just use a pieceof wire and link the entry 12v from the battery and touch the small control post on the solenoid.... one post goes to ground so be carefull. the control post from the key is the one you needto energize. if the ground part of the solenoid...
  11. C

    1977 Johnson 35 - Won't start

    solenoid need power to close the starter circuit and be grounded first thing to check before spending $$$ is to check if volatge is presented to the solenoid with the key at start... power to the solenoid from the key may be interrupted by the neutral switch. key the key on START and...
  12. C

    Constant high pitch alarm?

    well zm are known do block inlet pipes to water filtration systems could that have invaded a long sitting engine... maybe. but check the impeller theory first :) and faztbullet comment
  13. C

    Constant high pitch alarm?

    likely blockage of water passages from a broken impeller fin or just accumulated crud. lake water or salt water engine ? ? new impeller needed and pump housing must be inspected ... if lucky any broken parts may be lodged in there.
  14. C

    Fuel pump for 6hp 6904E

    they have worked for me if you do not want to rebuild the old one with a kit has suggested. Some keep the old pumps and scavenge parts from the new one. ...mostly diaphragms. First the top layer screw cap can be orieneted any way you need. Longer mounting bolts will take care of the...
  15. C

    Is there a guide to removing the powerhead on a 93 to 07 9.9

    909... why not simply scan a few critical pages and post them.... all with learn and should store them in their own files
  16. C

    1969 evinrude 25 horse 2 stroke won’t start

    clean the suspect points with a fine emery paper and rinse with carb cleaner. check proper continuity boot to engine frame (4-8 kohms) . check continuity while rotating the mag plate in case you have a broken wire in a bend ...or did you replace them ?
  17. C

    Fuel mux for 1960 Evinrude 10HP

    1 part of oil for 24 parts of fuel is richer than 1 part of oil for 50 parts of fuel 1 part of oil for 24 parts of fuel is good for black flies...
  18. C

    1969 evinrude 25 horse 2 stroke won’t start

    I am sure he meant FW....
  19. C

    1969 evinrude 25 horse 2 stroke won’t start

    see pic
  20. C

    Hmm...ok..1960 Evinrude 10hp running...

    well the motor stayed in good shape... not certain about the driver. :-)
Top