Search results

  1. S

    100:1 or 50:1?

    Found this article about Mr McCullochs life and what he created. Definitely proves what Flyingscott was referring to. Found it interesting learning about the history of him and everything he made....including his own oil. Not sure fixing the bridge was his best move. If you have some time...
  2. S

    100:1 or 50:1?

    68 is really low so probably your problem. Did you ever check with a different tester? Also, your engine won't start/run with the missing primer plunger (knob) unless you plug the rubber tubes going to it or pinch them off somehow. Now without the primer it will be even harder to start...so what...
  3. S

    water in lower cylinder/ Corrosion issues

    What do the pistons and cylinder walls look like?
  4. S

    100:1 or 50:1?

    Well also from what I was told, it all changed when Yamaha entered the market and omc had to react. I was told Yamaha was the first to silver solder their main bearings and changed all their tolerances. Most at the time would preach that the Japanese never invented anything, they were just...
  5. S

    97 Evinrude E50ESLEUS trim/tilt relay location??

    Wow, don't even have a trim N tilt (tnt) Looks like the old owner was pulling your leg or something. I take it you have a non-working switch on the control box. Anyhow....wire is what comes with the harness if you HAD a TNT! Funny.
  6. S

    2000 Johnson 15hp wont pump water

    So grommet was good and no holes in the draw tube?
  7. S

    100:1 or 50:1?

    Sorry didn't see Amsoil reference. From what I was told, from some top notch marine mechanics, was the tolerances and specifications of the motors needed to be designed for the mix ratio of oils. In the years that Omc made the recommendations of using 100 to 1 those tolerances weren't done...
  8. S

    Fuel line connection

    I suppose they were telling the engineers...."no, that's TOO good, make it crappier"
  9. S

    97 Evinrude E50ESLEUS trim/tilt relay location??

    Couldn't find your exact model but number thirty two on the picture is it. Follow the blue and green wires to it location. Good luck.
  10. S

    100:1 or 50:1?

    Just curious, what oils are you referring to?
  11. S

    water in lower cylinder/ Corrosion issues

    80, 70, 10.....? Time for the scrape yard.
  12. S

    100:1 or 50:1?

    Check other post, no need to make two posts by the way
  13. S

    Why is the choke won’t stay out, it feels a lot of pressure when I pull it out

    eBay has used ones. That is why your motor wasn't running right because you aren't using your primer correctly. Google how to use it. Here is an eBay link with the knob. https://www.ebay.com/itm/304560612657
  14. S

    100:1 or 50:1?

    Most likely you didn't kill it running 100 to 1 for that short of time and at low speed but maybe someone before you if they ran it at WOT for any length of time. What knob by the way? 68 is not good so you may want to retest with another tester. Not sure why it's running at home and not while...
  15. S

    Yamaha C60 knocking noise at higher revs

    Yes, and let us know if you resolve it.
  16. S

    Yamaha 90TRL propeller issue

    Excellent, now make sure you grease that prop shaft!
  17. S

    2007 Evinrude 115 Hp etec 2 stroke won’t turn over on cold starts

    You could remove the starter and bench test it. If you know how to do that. You can't jump the solenoid, at least not in the traditional way, but you can check voltage to it and through it. Remove the wire that goes to the starter and check voltage while someone turns the key.
  18. S

    2007 Evinrude 115 Hp etec 2 stroke won’t turn over on cold starts

    By the way, when it does start does it run fine? If so than it is electrical. Wire, soloniod or starter.
  19. S

    2007 Evinrude 115 Hp etec 2 stroke won’t turn over on cold starts

    Kinda weird. So I have a 2009 115 E-Tec with 950 hours. The only thing that has ever gone bad (knock on wood) is the starter. Mine didn't do that though, it started making a grinding noise. To me either, bad wire (ground or hot) or starter. Test voltage at hot side of soloniod while turning...
  20. S

    Yamaha F100 seized

    Huh? What are you asking?
Top