Search results

  1. S

    johnson 70hp 2 stroke 1995 shut down when warm

    Yes, and add carbs (cleaning/rebuild) and vro pump.
  2. S

    johnson 70hp 2 stroke 1995 shut down when warm

    And by the way, because I'm not aware of your boating knowledge, you did make sure you have oil in the reservoir? Because if your alarm is malfunctioning and no oil...... (No disrespect intended) Also, you can just check for spark you have to check for GOOD spark. That means a tester that...
  3. S

    johnson 70hp 2 stroke 1995 shut down when warm

    Well there is the pee stream. That says the pump is pumping. But that doesn't say if it's flowing around the engine. (Thermostat failure or passage ways plugged.) If you have a thermal gun (fairly cheap) you can shoot the heads when warm. Looking for 130 or so. Still think it's the fuel system...
  4. S

    johnson 70hp 2 stroke 1995 shut down when warm

    Well if it sat for a long time before you purchased it my guess it's fuel related. (Tank, hoses, carbs....) But it can be lots of things. Most on here will want model number, compression test numbers, spark test, etc. Then they will comment.
  5. S

    1987 Evinrude 110 success

    Awesome, it always rewarding when when you take a guess and it works! Not sure I would go back to the boat mechanic guy anymore.
  6. S

    1991 20HP Evinrude no acceleration

    I don't think it's overheating but you should check it. Sounds like it never runs fast good. You idle out and when you go to punch it on comes the problems. Could be an electrical component that only fails after heating up or like race says bad wire under the plate.
  7. S

    1991 20HP Evinrude no acceleration

    No slow mode or safe mode on that motor. Shoot the top of the head with a infrared gun and see your reading. Check plugs like Jimmbo says but I think Racerone is correct. An electrical component is heating up and misfiring. Again, please confirm, motor runs fine and then goes into that mode...
  8. S

    1991 20HP Evinrude no acceleration

    I concur.
  9. S

    1991 20HP Evinrude no acceleration

    If that isn't connected correctly or is stripped when you pump the primer ball has will spray out of that area. Easy to check.
  10. S

    1991 20HP Evinrude no acceleration

    After re-reading, your motor runs fine and then goes into that mode correct? If that is true, it probably is electrical. Do you have a timing light?
  11. S

    1991 20HP Evinrude no acceleration

    Just read this.....
  12. S

    1991 20HP Evinrude no acceleration

    Seems like a good motor, just has some kind of gremlin. This may seem a stupid question but is your primer knob pushed in? Hard to tell from the video.
  13. S

    Evinrude year

    Did you look under the flywheel or are they all missing?
  14. S

    1995 E70TLEOR wont run

    Sounds to me you lost a cylinder. Did you do a second compression check after the head gasket?
  15. S

    Johnson 8 pusher prop

    Yeah, I saw those too. My bet it's the 9 1/4 by 6 1/2. It's the biggest diameter, smallest pitch and is unavailable. I've never seen one on a Evinrude. Yamaha t9 and stuff but not rudes.
  16. S

    Johnson 8 pusher prop

    Racerone or whomever, Outboard...J8SRLEDS so 1996 extra long shaft. This is the prop on it. Can't find any info on them and can't read the size. Stock paint seem to have covered up the markings under the cone. Didn't really see anything on the parts breakdown either. Let me know. Thanks
  17. S

    Two wildly different compression readings, why? On in around 60 and on around 200?

    I've never heard of a reading so high, can water actually do that?
  18. S

    1972 johnson 75hp lift assist issue

    Here is some used ones on eBay. $70 plus shipping. Not sure if those help when raising...
  19. S

    1972 johnson 75hp lift assist issue

    Here is the correct part number for a 1974 70hp and while expensive they are available. The other ones I sent you were not available.
  20. S

    1972 johnson 75hp lift assist issue

    Forgot to post this.
View older results
Top