Search results

  1. jerryjerry05

    1974 chrysler 70hp motorl 707hf dies in 60 seconds

    Re: 1974 chrysler 70hp motorl 707hf dies in 60 seconds Absolutly BEAUTIFUL here!!! Tomorrow (Sunday)were going on our 2nd anual Toy Run.Should be a good ride.And not a hint of SNOW anywhere!!!! :) I've found that trying to adjust the kits usually ends up bad.Try cleaning up the old and check...
  2. jerryjerry05

    Is my boat suppose to have pee hole?? Force 40 1999

    Re: Is my boat suppose to have pee hole?? Force 40 1999 That motor might not have one.But you can install it easily. See pic #20 remove it and install an L shaped fitting and drill a small hole.Then a piece of hose.
  3. jerryjerry05

    1969 Chrysler 35 HP - New to Me, Runs Bad

    Re: 1969 Chrysler 35 HP - New to Me, Runs Bad Sometimes the only way to remove the flywheel is a BIG 3jaw puller. Wanna try this? I'll give instructions.J
  4. jerryjerry05

    1986 50 force

    Re: 1986 50 force NEVER start for any length of time.1 second can be too much!!!15 is way too long. That motor need s a special muff.The big one don't fit right see the pic.J
  5. jerryjerry05

    transom saver or what

    Re: transom saver or what There should be a trailer bracket for that motor. e-bay. See pic #24.You put it in place and lock it down with the lock switch. Probably easier to get the transom saver. Like Fucawi said if you have the room drive with it down.J
  6. jerryjerry05

    Changing over,Hey Frank??

    Changing over from the Manapower to the Prestolite. What parts need to be modified??? Frank you posted once about this.Can't find it. Thanks,Jerry
  7. jerryjerry05

    1982 Chrysler 85 No Spark help needed

    Re: 1982 Chrysler 85 No Spark help needed It takes a lot of force to remove the flywheel.It had 95# of tourqe on it. I use a BIG 3 jaw puller(see pic) and a 3/4# sledgehammer.The hammer in the pics is only a 2# use a bigger if you have one. Install the puller and leave the nut on a few...
  8. jerryjerry05

    Question about prop when in neutral, forward, & reverse

    Re: Question about prop when in neutral, forward, & reverse Hope this helps. Push down on the rod in the one pic.All the time spinning the prop either way.Then the prop pic.Pull up on the right hand side(one with the red thing)This will help spin the drive shaft. A pair of Vice-grips will work.
  9. jerryjerry05

    1990 Force 50 horse run issue

    Re: 1990 Force 50 horse run issue Do a compression/spark test.then rebuild the fuel pump. You running it in the lake or the drive?? The muffs you use could be the wrong ones.The right are in the pic I added. Check the impeller.Sounds like it's overheating.J
  10. jerryjerry05

    Starter problems???

    Just bought a 125/88 for parts.Owner said it hardly turns over and won't start. I replaced the starter with a back-up. I noticed the flywheel had a wobble(not supposed to).I removed it and saw the keyway was sheared. Cleaned up the keyway and used a good flywheel.The other 's magnet was...
  11. jerryjerry05

    Forgotten trim/tilt bracket

    Re: Forgotten trim/tilt bracket Pic of the lock bar. Send me your e-mail.J
  12. jerryjerry05

    Forgotten trim/tilt bracket

    Someone a while ago asked me about a tilt bracket.I promptly forgot. Well I was digging through my stuff and found it. Send me a PM and we'll talk.
  13. jerryjerry05

    Chrysler Economate 3.5 runs only at half-choke

    Re: Chrysler Economate 3.5 runs only at half-choke This might not be quit like your carb.#23/#16 Start with the carb.Take it apart and make sure there are no particals in the jets.No cloggs in the ports.A partical the size of a pin point can stop a motor from running.One time I cleaned a carb...
  14. jerryjerry05

    '87 50hp force flywheel problem(Am I Screwed?)

    Re: '87 50hp force flywheel problem(Am I Screwed?) You need a big 3 jaw puller.Install it and tighten it down and tighten it some more.Then with a hammer(oh yea reinstall the nut a little way)hit the threaded screw with the hammer. It should pop off.If not tighten it some more.I use an air...
  15. jerryjerry05

    I think i fixed it. what do you think .THANKS TO ALL OF YOU

    Re: I think i fixed it. what do you think .THANKS TO ALL OF YOU Spark check.Use a tester like the one in the pic. The spark should jump at least 7/16 with a good coil. In-line testers can be used for running and testing in the water while under way. Very well could be a bad coil all along. You...
  16. jerryjerry05

    96?? Mercury 9.9 4St

    9.9 4 stroke. I start it and it has a lot of oil comming from the blow-by hose. Seems to run right.Starts right up. The owner over filled it with oil by about 1/2 to 3/4 a qt. of oil. I drained it and refilled to the proper level.
  17. jerryjerry05

    Lower unit removal.

    Need to know how to remove the lower unit on this motor. Thanks in advance.Jerry 96 Johnson.30 hp E30ELEDE G 04162578
  18. jerryjerry05

    Help with 1998 50hp Force Motor

    Re: Help with 1998 50hp Force Motor #3/4/5/6 The very bottom of the drive is a slotted screw screw.That's the drain and where you fill.Closer to the cavitation plate is a slotted screw that's the vent. Check that after you use the boat.Look for water and metal shavings. The gas needs 1pt of oil...
  19. jerryjerry05

    KARLA here are the pics.

    #1 is not the way to remove them.It can scratch the mating surface. #2 shows the seal in an old pump(same procedures) #3 shows it from the bottom. #4 shows the screwdriver in from the bottom.Put the driver in the bottom and hit with a hammer.It should drive it out without damaging any sealing...
  20. jerryjerry05

    1st time lower unit removal, what is this part and where does it go?

    Re: 1st time lower unit removal, what is this part and where does it go? Try to knock them out from the other side. Hammer/large screwdriver.Or a puller see pic.Just watch how they come out.Two together are back to back or face to face.The new need to go back in the same way. Same with the...
Top