Search results

  1. Lou C

    RWD Tow Vehicle Launch Issues?

    How we used to go on slippery surfaces with RWD...before everyone had an SUV, the only people who had Jeeps were sportsmen and gas station owners with a CJ with a plow or push bumper on it...We had GM full sizes early to mid 70s and no limited slip, so we used to put some 40 lb sand bags in the...
  2. Lou C

    Trapped air after filter change

    I usually fill the fuel filter nearly full before threading it on but the system should self bleed.
  3. Lou C

    Burning Rubber Smell and White Smoke from Engine?

    Glad it was a simple solution!
  4. Lou C

    5.0GL-C won’t get on plane

    There has to be a way of getting at the connections for the fuel tank. Some boats like mine has a hatch that you remove, others have a circular pie plate cover that comes off to reveal the connections. My boat had a similar problem & it was the anti siphon valve which is what the fuel line from...
  5. Lou C

    Altenator and Starter Replacement

    I’ve never used them but some members on here have; maybe post up that question
  6. Lou C

    2012 VP 300 C-A Exhaust manifolds getting too hot - DTC 441 & 442

    An exhaust elbow that was used in salt water can look great on the outside but could be all rotted out under the hoses where you can't see and the ONLY way to tell if your cooling passages are open is to take it apart, if you are suspecting a blockage due to hot running temps. In your case the...
  7. Lou C

    2012 VP 300 C-A Exhaust manifolds getting too hot - DTC 441 & 442

    I Thought that's what I said...if there are air pockets not filled with coolant, then you have hot spots...
  8. Lou C

    Altenator and Starter Replacement

    actually they are not, water will kill them! especially starters.
  9. Lou C

    Altenator and Starter Replacement

    It is a metal screen that prevents flames from ignited vapors from escaping from the electrical component; so for example if an explosive mixture of fuel vapors gets inside the starter, alt or distributor and is ignited the screen stops the flame from traveling outward & igniting the rest of the...
  10. Lou C

    Burning Rubber Smell and White Smoke from Engine?

    Sounds like your exhaust mat be overheating if those manifolds & elbows are original they might be way past their expiration date (clogged by rust, not cooling & overheating the rubber exhaust hoses). Water cooled exhaust on an inboard has to be maintained unlike automotive exhaust. Get an IR...
  11. Lou C

    Altenator and Starter Replacement

    Yes. They are ignition protected. Do not use auto anything on your I/O for: Alt Starter Distributor Carb Fuel pump I like ARCO for alternators & starters
  12. Lou C

    2012 VP 300 C-A Exhaust manifolds getting too hot - DTC 441 & 442

    Even if the engine doesn’t overheat due to the design of the exhaust manifolds if the air pocket just happens to be right near the location of the temp sensor then you can get those codes I’m guessing. So for it to not have any codes you probably can’t have any leaks at all in this system. I’d...
  13. Lou C

    Stalls out hot

    OMC used a 160 stat
  14. Lou C

    Converting to carburetor from mpi 350 mag

    Agreed that’s what I thought worries about depending on a regulator to not overpower the carb
  15. Lou C

    OMG - I got an oversized load permit !!!

    Wow that camera I really like!
  16. Lou C

    5.0GL-C won’t get on plane

    There are also 2 other things that could be related…. Anti siphon valve on the fuel tank fitting & the screen on the pick up tube in the tank. There may be a small screen in the carb inlet area with on Holley carbs (I think that’s what you’re working on) that you can check too….
  17. Lou C

    Converting to carburetor from mpi 350 mag

    Also you are going to need some parts to make the throttle hookup which you can find on Holley’s website
  18. Lou C

    Converting to carburetor from mpi 350 mag

    That’s a good question actually for anyone who wants to convert. You need a low pressure fuel pump & the unit you have for EFI won’t work unless there’s a way to just use the low pressure pump separately (carb needs only 4-6 psi fuel pressure vs EFI much higher). So you probably need to buy a...
  19. Lou C

    Stalls out hot

    Float sticking or crud in the needle valve = flooding
  20. Lou C

    Just thought I'd share a nice photo.

    The dock in our neighborhood beach community....sunset.....coastline in the far distance is Connecticut approx 10 miles across LI Sound....
Top