Search results

  1. C

    1999 115hp evinrude ficht

    btw... check the VST ...your FICHT it likely has a small conical filter on the return manifold fuel supply from the injectors. it can block/impair fuel flow causing inj. issues ....incl cooling if fuel doe not flow Even on the 2005 ETEC books they don't show it !!! CAREFULLY remove the...
  2. C

    1999 115hp evinrude ficht

    yes the ETEC inj. in the video are different from FICHT . The video was to show the basics of inj. cleaning you are aware that changing injectors requires injector data spec updates to be loaded in the in the EMM otherwise engine damage will most likley happen at higher RPMs here is a...
  3. C

    1999 115hp evinrude ficht

  4. C

    1999 115hp evinrude ficht

    comp ok sparks OK ... now you need fuel the best way to know if the injectors are spitting gas is to remove a plug ground the plug properly and insert a paper strip inside the cyl. if it does not get wet with fuel the injector is/are not spitting fuel in the cyl and the engine will...
  5. C

    90 Etec tilt and trim pump leak

    Do let us know how it all works out :-)
  6. C

    Do you make your own gaskets ?

    I have made some where pressure and heat is not a critical issue ex: impeller base gasket , intake manifold etc... Cyl heads = OEM !!
  7. C

    What do I do??

    try used parts places like Tim'S outboard or Doug Pen or go to AOMCI classifieds...
  8. C

    90 Etec tilt and trim pump leak

    do you have the manual ...some seals differ check in at the ETEC user board to confirm part# https://www.etecownersgroup.com/?forum=136483 btw check oil type for ETEC T&T book says to use a special Evinrude T&T bio oil $$$$$ vs common mineral stuff $$ after much...
  9. C

    1971 Evinrude fisherman, not pumping water

    if never done.. a reseal job can be a challenge I woud do a pressure test if you can (used soapy water spray) to see if you have bad seals. otherwise new nylon washers may... solve the problem check the small shifter (phipps) screw for leaks on my last reseal of a 5.5 I used...
  10. C

    1976-1978?? 9.9 flywheel nut

    if you do go hardware store at least l get a nut with nylon locking head to hold it down !
  11. C

    Evinrude 9.5 vs 8hp speed test

    something in me was left over.... from my early days of boating in the late 60s
  12. C

    Evinrude 9.5 vs 8hp speed test

    great kicker for trolling and emergency back-up to modern technology :) but... I replaced it with even better gas guzzling wise anyway a nice Merc single cyl. 4hp :-)
  13. C

    2006 Johnson 9.9hp need help…

    I would use paper gasket material easy to cut with an exacto knife and hole punch. you can try thin cork... no harm in trying
  14. C

    1971 Evinrude fisherman, not pumping water

    Crow pie is served sometimes ..and somtimes deserved :-)
  15. C

    2006 Johnson 9.9hp need help…

    carb jobs are mostly cleaning out obstructions like dried gas, sticky needles so if you do not break the gasket reassembly is usually satisfactory. it certainly seems that fuel is flowing ... if not to much... check the float... enricher
  16. C

    1971 Evinrude fisherman, not pumping water

    may as well check everything...for crud
  17. C

    1971 Evinrude fisherman, not pumping water

    remove the gc & spin the drive shaft in the bucket of water .... make certain water gushes out of the impeller housing... if ok work top side reinstall GC align the water tube if not.... check for water restriction into the GC water intake cavity below the impeller housing
  18. C

    Evinrude 9.5 vs 8hp speed test

    deleted
  19. C

    1971 Evinrude fisherman, not pumping water

    exhaust or steam ...check pH temps with infrared scanner (cheap tool to have) pull the thermostast check passages visually for blockages. pull the cyl head check /clean water jackets for blocage replace cyl head gasket
  20. C

    Temperature alarm goes off as soon as you turn on the ignition.

    any chance the temp sensor wiring is grounded (chaffed) ??
Top