Search results

  1. C

    Tiller Conversions Seahorse 35

    chineese coils are fine but mail is slow get some condensers to since yours are most likely bad points you can clean and adjust to 0.20 or use the vom method...
  2. C

    1994 Johnson 175 turns over with key switch off?

    disconnect the control wires on the selenoid if it cures the problem then the selenoid in OK but is being energized look downstream. first try to tap the key assembly to see if it releases the selenoid ... having reconnected the wires of course. if it clears the...
  3. C

    Help me decide- Johnson 30

    you really should check out compression ... must be me but I do not understand folks beating their motors mdl and serial#s worn to much ??? was it polished to much .. hardly father in law's ? .... maybe maybe not but it was certainly somebody's father in law . your call me...
  4. C

    Johnson 25HP 1985

    just torque it by hand till tight has much as you can and back out to install the cotter pin
  5. C

    79 35hp evinrude wet plugs

    in the diagram the rectifier does not draw current via the fuse so it is unlikely it would blow the fuse. the rectifiers feeds +12v to the bat. via the fat post (red) on the selenoid.
  6. C

    4 HP Evinrude Coils

    this is what we all find under old motors like yours although 1980's is not that old for cracking no offense but 2 bad coils in one motor at the same time is somewhat bad luck .... make certain you use the proper scale to read low ohm values across the primaries then a higher scale...
  7. C

    4 HP Evinrude Coils

    these coils are common to OMC magnetos for about 20-25 years and have changed numbers across the years so don't worry to much about finding the same numbered coils it is critical that to avoid any wrong answers from folks helping out on your project that you list the engine model on...
  8. C

    Head gasket orientation 1990 4hp E4RESR

    see video... (683) Can JB Weld fix a cracked cylinder head? See the proof!! - YouTube I think you could fix that small indentation with JB on a water cooled cyl head
  9. C

    Head gasket orientation 1990 4hp E4RESR

    How to use AlumiWeld, do it yourself aluminum propane welding repair kit 2 important point clean the part to remove all form of oxydation (SS brush will do) heat the part NOT the rod heat the part till the rod melts grind the excess aluminum back to what you want I used the product...
  10. C

    79 35hp evinrude wet plugs

    typical layout...the fuse feeds the B post on the key which shares it with the selenoid to start but.... reverts to feeding the ACCESSORIES "A" terminal on the key while "ON" any problem on the accessories distribution . or faulty switch will blow the fuse ex: bad tach, bad...
  11. C

    50473m 50hp evinrude lark ignition wiring diagram

    continuousWave: Whaler: Reference: Ignition Switch maybe you can find something in here to help
  12. C

    Head gasket orientation 1990 4hp E4RESR

    just saw a you tube with a fix similar to your problem using EXTREME HEAT steel epoxy Amazon.ca:Customer reviews: J-B Weld 37901 ExtremeHeat High Temperature Resistant Metallic Paste - 3 oz good up to 500 deg. may work for you ?
  13. C

    50473m 50hp evinrude lark ignition wiring diagram

    can't vouch it is 100% if you had more wires it would be a problem :-) trace back the wires to find out where they go and do
  14. C

    Newly bought Johnson 7.5

    impeller is the rubber star in the pump housing visit utubes for lots demos
  15. C

    1980 70hp Evinrude clatters and hard to get into Forward gear

    is this a new problem recently ..sounds like some linkage is not adjusted properly or gears destroyed partially by improper shifting procedure by previous owner any metal chips on the oil plug magnet ??
  16. C

    Head gasket orientation 1990 4hp E4RESR

    tab up and holes lined up top left and right are not symetrical like the middle and bottom bolt holes so you must line up the top bolt holes with the gasket
  17. C

    50473m 50hp evinrude lark ignition wiring diagram

    is this any good ... Evinrude Ignition Switch Wiring Diagram - Bing images
  18. C

    Exhaust coming out under the power head

    rats mice bees who knows what lurks up that exhaust cavity :-) a dead snake maybe ...
  19. C

    4 HP Evinrude Coils

    well... the 1982 4hp uses good old 0584477 available everywhere including china but.... coils (2) just don't "stop working" tell us more before spending good money . cracked ?? what ohms do you measure from the secondary High voltage pin and primary wires (usually 4-7 Kohms)...
  20. C

    Evinrude 1975 85 hp electrical starting issue

    still raining ...?
Top