Search results

  1. R

    74 stringer electric shift rebuild

    Try another prop first.-----I think the hub is slipping.-----If it is the drive spring slipping the lower unit must come apart for inspection.----Mark the prop and prop hub.----Test run and see if marks moved.
  2. R

    1998 Johnson 115 Prop Shaft Seal Replacement

    Remove 2 bolts #28 and pull out item #24.-----install new seal and item #17.-----Install a new water pump impeller as well.
  3. R

    E15REOD idle

    The high speed jet is not anywhere near plug #17.
  4. R

    E15REOD idle

    Item 17 is a plug.----It does nothing but act to seal out air.
  5. R

    1988 Johnson 28hp only starting for a bit when wires are switched

    Maybe check for a sheared flywheel key as well.
  6. R

    1975 chrysler 4.9 wont start

    Tried switching plug wires?----Where is the flywheel key ?---Does spark jump a gap of 1/4" or more on a test device ?
  7. R

    1969 evinrude 25 horse 2 stroke won’t start

    Never had one bounce on the floor !
  8. R

    1969 evinrude 25 horse 2 stroke won’t start

    I have pulled many flywheels.-----Never leave the nut on.-----I doubt that the " crankshaft " will go flying off as per above post.
  9. R

    1990 Force 120HP #2 Cyl zero compression and upon opening piston shows damage

    Some will argue.----About $17 each for new.----I suggest you install new !!
  10. R

    Fuel mux for 1960 Evinrude 10HP

    Need to review your math.-----24:1 is more oil than 50:1.-----Need to understand the concept of why oil is mixed with gas.----Need to understand the concept of lubrication in a 2 stroke engine !!
  11. R

    Fuel mux for 1960 Evinrude 10HP

    The original mix was 24:1------But today you will get many different opinions as to what will be proper lubrication for that fine motor.----As previously indicated to you it has a bronze bushing ( if still original ) on the wrist pin.----And that is a known weak point !
  12. R

    1988 Johnson 28hp only starting for a bit when wires are switched

    My wild guess is that wires from CDI / powerpack to the coils were switched by a club fisted individual.-----Orange / blue stripe should be on the top.----What else do you know about this motor ?----How did it run for you last season ?----Post the compression test numbers here.
  13. R

    68' Johnson 20hp (FD 22M)..Want to add starter..

    I am also looking to get a local Mennonite shop to see about reproducing parts.----Should not be hard to cast that bracket in SOLID aluminum to then machine bolt holes and hole for the starter.----Should be able to produce that at 1/4 the market price !!
  14. R

    68' Johnson 20hp (FD 22M)..Want to add starter..

    I was at a dealer / boat shop a few years ago.-----Found an 18 HP in the scrap bin.----Had the electric start on it.----Free to take it away.-----Keep your eye on Craiglist / facebook etc and see if a $100 donor motor comes along.
  15. R

    68' Johnson 20hp (FD 22M)..Want to add starter..

    It is the golden rule of supply and demand.-----Those with the supply are doing the demanding.-----Or I always say -----" Farmers do not have to pay cows to chew the grass.----Why do they want so much for milk and cheese " ? -----Your location ?
  16. R

    Prop for my 1960 Evinrude 10hp sportwin

    It is a right hand prop.----There are some websites where YOU can look up the part #----Hint---a 1973 model 9.5 HP might use the same prop.
  17. R

    Need Help with Ignition

    Or a repair kit from the ----hooflungdung-----Was used.----Stick with factory quality parts.
  18. R

    Need Help with Ignition

    Choke must be closed to start a motor.-----Water must be 6 or 8" above the impeller when testing in a bucket.----Sound like it is not in your case.
  19. R

    Evinrude 7518 powerhead base gasket.

    Agreed----303467 is correct.----Found those same 10+ listing as well.
Top