Search results

  1. jimmbo

    1998 Mec 150 black max

    I doubt the Idle Circuit can go rich enough to cover the loss of the Accelerator Pump, without other modifications being made.
  2. jimmbo

    How many turns out do you set the low idle jet from lightly seated

    You are adjusting Screw# 15? Did you have/use Rebuild Kit? If no, what parts did you replace?
  3. jimmbo

    How many turns out do you set the low idle jet from lightly seated

    Can you provide a Model #, so I can look up the correct carb?
  4. jimmbo

    1998 Mec 150 black max

    Part # 17-810747 - STEM NLA You might need to get a used carb and salvage the Stem, and likely the Spring under it
  5. jimmbo

    How many turns out do you set the low idle jet from lightly seated

    And you blew out all the passages with compressed air, and returned the carb to the Solvent for more soaking a few times?
  6. jimmbo

    70 hp Johnson wont accelerate

    Welcome to iboats A year/Model # would be nice as it allow us to determine if there is a Choke or other Enrichment System.
  7. jimmbo

    How many turns out do you set the low idle jet from lightly seated

    I suspect the carb needs a thorough Cleaning
  8. jimmbo

    2021 Mercury 115 Pro XS cavitating

    Cavitating or Ventilating? Lowering the motor will reduce Ventilation, but not Cavitation. Normally trimming the motor in, not out, reduces Ventilation, as it buries the Prop deeper in the water. Can you post a few Well Taken Pics of your setup. By 'well taken', I mean shot parallel to the...
  9. jimmbo

    35 hp johnson loses power at high rpm.

    Check for Restriction/leaks in the Fuel System. Fuel Filter or Screen, may be plugged. Hoses might have decomposed internally, Screen on pickup in Gas Tank, leaky O-rings or Primer Bulb on Gas Hose, allowing air in. Also, if Fuel Pump has a Hose going to the Crankcase for the Pressure-Vacuum...
  10. jimmbo

    Peter backs boat down the ramp like a pro

    Last year, way too shallow of a ramp.
  11. jimmbo

    1996 Evinrude V6 150 (60 deg) Looper Problems

    The compression numbers are quite low. Redo the Compression Test with a Different Gauge. Unless the engine is in good Mechanical Shape, it is never going to run well
  12. jimmbo

    Mercruiser 5.7 wanting to stall at idle after driving around

    Fuel, normally only flows thru the Discharge Nozzles in the Venturies, when there is enough Airflow, to pull the Fuel out, from the proper Fuel Level in the Float Bowl. There is not enough Airflow at Idle, even several hundred RPM above Idle at low load to do that. If fuel is coming out of the...
  13. jimmbo

    Mercruiser 5.7 wanting to stall at idle after driving around

    A 1980's Automotive Q-jet would look quite a bit different forward of the Primaries
  14. jimmbo

    Mercury 60 HP engine question

    If there is a Cap, the tank should be under it, so if it was removed, you have to mix the oil in with the Gas. Oil TCW-3, at 50:1, basically 16 ounces for every 6 US gallons of Gas
  15. jimmbo

    Mercury 60 HP engine question

    Is there a oil tank inside the Engine Cowl?
  16. jimmbo

    Mercury 60 HP engine question

    Well it has Electric Start, is likely a Wheel Steering model, Does it have Power Trim?
  17. jimmbo

    Mercruiser 5.7 wanting to stall at idle after driving around

    I can hear the Stones. I see a Zinc Carb, and I want it painted Black
  18. jimmbo

    Mercruiser 5.7 wanting to stall at idle after driving around

    A 75 Olds had no electric heating element on the choke. In 75 there was an Altitude Compensator in a Lot of Q-jets, some also had a Second Power Piston and Metering rod, on the Primary Circuit. In 76 the Altitude Compensator was removed, I know my 76 Olds 88 455 didn't have it, though there was...
  19. jimmbo

    Mercruiser 5.7 wanting to stall at idle after driving around

    It might not be USCG legal. I doubt an 80s Pontiac Carb is calibrated for use in a Marine Application. Even if the Jets, Metering Rods, and Power Piston spring were changed, the Idle and Off Idle Fuel Circuits could not be easily recalibrated, and same goes for all the Air Bleeds that are part...
  20. jimmbo

    Mercruiser 5.7 wanting to stall at idle after driving around

    I have a Q-jet I liberated from a 67 Olds Toronado 425. Back then they used a Clip that went around the Power Piston Tube, that had a Tang to keep the Power Piston from jumping out. A couple of Year later they went to the Phenolic press Washer shown in your pic. On my 67 O-jet, the Secondaries...
Top