Search results

  1. R

    1995 70HP Force, cranks but wont fire.

    Your motor and some effort has to be put in by you to check a few things.
  2. R

    Evinrude year

    Missed that part in the brochure.------I should dig through my parts books as the 20 HP models were listed in them.
  3. R

    1986 20hp Johnson long shaft low compression

    Wishful thinking on your part.-----But good luck and do what you like.
  4. R

    Evinrude year

    The 1977 models use the same 30 cubic inch block as the 35 HP.-----Have a 79 model 20 HP myself !!
  5. R

    1986 20hp Johnson long shaft low compression

    Remove cylinder head.----Followed by inspection.
  6. R

    Evinrude year

    The 20 HP was still marketed in CANADA up to 76 I believe..----It is as simple as that !!-----Not sure why that is an issue for you.-----Same ignition as the 25 HP models !!
  7. R

    1986 20hp Johnson long shaft low compression

    Remove cylinder head and inspect cylinder walls.-----Or perhaps you need a better gauge.
  8. R

    Just rebuilt the LU w new Oem gears,seals. Having trouble reinstalling pinion gear. 1972 Rude 65hp

    The driveshaft has to line up.------Best to remove the oil pump and start over.----And have you selected the correct shims for the pinion ?
  9. R

    1999 50hp Johnson only starts at full throttle

    Model # is ?----How did it run for you last season ?-----Need to post compression numbers.-----Does spark jump a gap of 3/8" or more ?-----Check flywheel key.-----Pushing key in and holding it in while cranking it over ?
  10. R

    1995 70HP Force, cranks but wont fire.

    You must install a new water pump impeller.----Test over heat horn ( if equipped ) on this motor.----Mixing gas and oil at 50:1 in your tank ?----Agreed----Do a compression test.---Post the numbers.
  11. R

    Oil on choke?

    This is on a 3 cylinder 25 HP 2 stroke.-----A wonderfully rugged and simple machine.
  12. R

    1962 Merc 450 restoration ..

    Using a bit of heat ( propane torch ) the bearing will usually fall out on the work bench.
  13. R

    1990 force problems

    Sounds horrible to me.-----Stop the revving and hoping.-----Do a compression test.----Post your numbers.----Forget the blinky tester.----Does spark jump a gap of 3/8" on a test device in open air??
  14. R

    Evinrude year

    well----if in Canada use---------evinrudeparts.ca-----I believe you will need to believe that the 20 HP is essentially the same as the 25 HP !!!
  15. R

    50HP Evinrude - Coils not grounded

    Looks like there is a ground to me !!!
  16. R

    Evinrude year

    Well-----The 20 HP was marketed in Canada.-----Your local dealer would have the parts listing.----Or use the 25 HP listing for most parts.
  17. R

    Engine Overheated on Evinrude

    Sorry----In 66 the general public understood that you had to change impellers / visit the dealer.-----And yes there is very clear indicator for water pump function.----Many folks today are only able to push a button and wait for engine to start / run for them.
  18. R

    Evinrude Big twin 40

    The NOZZLE is not adjustable.-----The high speed jet in the float bowl is not adjustable
  19. R

    45hp Commercial Year?

    Looks like about a 93 model.
  20. R

    Evinrude year

    The 22 cubic inch motors were made to 1976 all basically the same save for the later ignitions.
View older results
Top