Search results

  1. R

    1997 Johnson 70 hp water pump impeller o-ring

    Sorry----The gearcases are the same !
  2. R

    Stumped on ignition problem

    ???----You would use the timing light as a " poor man's scope "----So if the light flashes steady at idle and does not flash steady as you speed , up it is telling you there is a spark issue.----May help you determine which cylinder is the issue !!
  3. R

    1997 Johnson 70 hp water pump impeller o-ring

    Sorry -----But there is no difference between a 97 to 98 model.
  4. R

    Trailer tires dryrotting again

    I used to work in a tire factory.-----I say----" Tires are all black but they are not all the same "------It is a shame that these inferior products have crept into our daily lives.
  5. R

    1979 115 hp 115999R Evinrude Outboard runs great in test tank at fast & slow idle, does not in when I put in the water

    Good luck with your trouble shooting.
  6. R

    1979 115 hp 115999R Evinrude Outboard runs great in test tank at fast & slow idle, does not in when I put in the water

    Damage to pistons and rings.-----Post pictures of pistons and rings when you look in there.----You did confirm that starter / battery and battery cables are in good condition ?----In my opinion this should be easy to diagnose !
  7. R

    1979 115 hp 115999R Evinrude Outboard runs great in test tank at fast & slow idle, does not in when I put in the water

    You have a bad test gauge or a motor that needs rebuilding.----Remove the wee bypass covers on the side of the motor ( 6 screws each ) and look at pistons and rings.----Lucky you if it is just blown head gaskets.
  8. R

    Excessive VRO Oil Consuption

    There is not much that can go wrong with the oil side.----Just a wee piston o-ring running in a small metal cylinder.-----Do check the check valves in the air motor and look for air leaks.
  9. R

    1988 15HP Johnson outboard grey oil after motor flusher

    Quite normal for a 2 stroke after idling / running on muffs.
  10. R

    Manually tilt 1972 65hp evenrude

    On a 1972 model 65 HP the plugs should be YELLOW.-----So work / modifications have been made.---All bets are off !-----If this thing was in front of me I could likely sort it out.----Was working on outboards before yours came out of the factory.
  11. R

    Manually tilt 1972 65hp evenrude

    Post picture of the wires installed on your ignition switch.-----And does the control box cable and motor both have a big YELLOW plug , yes or no ?
  12. R

    Manually tilt 1972 65hp evenrude

    Some will argue.----Well I can see a mounting bracket as used in 72 is not there.-----But perhaps someone used a different technique.----Folks are very creative these days.----And yes it does show an electric tilt bracket installed but no motor and pump !!----You may think that they only started...
  13. R

    Manually tilt 1972 65hp evenrude

    It looks like an electric tilt motor and pump was installed at one time.-----Also looks like an important mounting bracket for the outboard itself is missing.----Is there a little lever at the front of the motor that needs to be flipped over for manual tilt.-----Please be clear on what you have...
  14. R

    1950's Yachtwin Fisherman Challenge project! Need help

    Are you 100% sure both powerheads used the same gasket ?----The gasket between the powerhead and the exhaust housing ?
  15. R

    Stumped on ignition problem

    Test run with timing light hooked up 1 cylinder at a time.----Observe the flashing light when motor acts up.----Overheating ?
  16. R

    1950's Fleetwin Fisherman Challenge!

    Actually the pressure tanks work well and are very reliable.----You pump fuel into the carburetor.----When motor start it quickly pump crankcase compression into the tank to keep fuel flowing into the carburetor.----Repair kits and parts are available.
  17. R

    Johnson 150 Rebuild/Remanufacture Guidance

    These tools work like a charm.----Have 2 of them and no modifications needed.----Only now do I need to modify them as my arms do not look the same as when I was the high school wrestling champion !
  18. R

    Damaged Tilt End Caps, how to remove

    Salt water motor ?------Make a tool using 1/4" X2" flat bar.-----Drill the holes bigger or new good holes to use this tool ?
  19. R

    Will not turn over with all plugs on.

    These rods are ----CRACKED-----As part of the manufacturing process.----The cap only fits one rod and one way ( dots ) on one side.-----So the surface is irregular.----You assemble these carefully making sure the edges line up.----I use a pencil lead to see if it catches at all.
  20. R

    1970 Johnson 60HP

    Those solenoids are very good and reliable.-----How did you determine that shift solenoids where bad ?----You do know that motor must be turning in order to shift I hope.
Top