Search results

  1. R

    95 130 HP Johnson looses power / runs at 10 mph

    Check for spark.----Spark must jump a gap of 3/8" or more on each lead.-----Perhaps test run with a portable tank and hose.
  2. R

    Carburetor frustration

    The electric primer is a valve.----It is not a pump.-----When the engine is cranking and the key is pushed in ,the FUEL PUMP pushes fuel through the primer valve directly into the motor.-----In my opinion the VRO pump is very simple.----Easy to take apart for inspection / repair.
  3. R

    Carburetor frustration

    Do you understand what the primer solenoid does ??---Please explain how it works.----The primer solenoid is a wonderful device.----Remained unchanged for nearly 30 years.----It works very well.---The 2 port pump worked on the crossflow V-4 engines.----It is not practical to use a 2 nipple pump...
  4. R

    Carburetor frustration

    Fuel component package has a FUEL pump looking thing on it.----That unit is used on many small motors as the fuel pump.----On your motor it was converted to be a vapor extraction pump.----Replace gasket #26.---Check cover for warpage.----Some will argue.---I doubt you need to resort to an...
  5. R

    Lower Unit Compatability

    As clearly state 76 and newer.----You can adapt the 1974 unit.----If bolted on it will shift to reverse when you select forward.----Somewhat inconvenient.----You would have to change linkages on the motor.-----And before you ask no there is nothing you can do in the control box !!
  6. R

    Johnson V4 swivel grease

    Corrosion products form between the bushing and aluminum.-----Oxygen joins with the aluminum to form aluminum oxide ( white powder ) thus there is more material now ( oxygen ) and the works jams up !!
  7. R

    Johnson 4R71D Resurrection Attempt

    It will run with 70 PSI.----You may be surprised how well it runs with that.-----$100 for a good used lower unit is a good deal.----Install a new impeller.
  8. R

    1972 Johnson 85hp Power tilt

    Your location ?
  9. R

    Top cylinder not firing Johnson 55ESL69A

    Your location ?-----Used parts may be easy to find.
  10. R

    Lower Unit Compatability

    Just 3 cylinder motors 60 / 70 HP from about 1976 to 1988 use the coarse spline.----I repeat just the 3 cylinder models use the coarse spline.
  11. R

    Could a 4 blade actually be faster?

    Have your boat weighed.----At one time " winner boats " used individual plastic containers for flotation.-----Not sure about yours.-----If boat is water logged it will be slow !----Note---Some high performance offshore boats use 5 blade props.-----Blades may not all be in the water all the time.
  12. R

    Big twin 40hp shear pin material?

    I used to do some anodizing of aluminum and also magnesium.-----Uses electricity in a chemical bath.----Quickly coverts the surface aluminum to an oxide.
  13. R

    Johnson 70 hp 3 cyl / 2-stroke dies when giving more throttle

    Could be a slight leak / mis-alignment of the reed valves.-----Or an issue with oil recirculation passage way on reed valve mounting plate.----Remove carburetors / inspect reed valves.--Replace gasket.
  14. R

    Johnson 70 hp 3 cyl / 2-stroke dies when giving more throttle

    You do not understand the concept.----You lay the timing light on a seat so you can observe the flashing of the light !----No flash means you have lost spark !----Does spark jump a gap of at least 3/8" ( 1 cm ) on a test device ?
  15. R

    75HP Evinrude Loses Power During Acceleration

    ??----The thing with the red lever is the electric primer valve.-----That wonderful unit essentially replaced the choke flappers on your motor.---The roller opens throttle plates and has nothing to do with choking this motor.-And why are you referring to a low gear cable and a high gear...
  16. R

    Johnson 70 hp 3 cyl / 2-stroke dies when giving more throttle

    Run with a timing light hooked up.----One cylinder at a time.----See if there is a spark issue as boat speeds up.-----Running with VRO in service ?---Tested VRO oil output ?-----Or a simple non mixing pump with 50:1 in your tank ?-----Perhaps test run with another tank and hose.
  17. R

    1978 Johnson 75hp compression

    Test with another gauge.----Or if gauge is good you have serious piston / ring problems.
  18. R

    Badged as 9.8, Serial A901055 Running on One Cylinder Only

    You need-----Spark at the right time.----Compression in the cylinder.----Correct ( not too much or too little ) amount of fuel.------Compression in the crankcase.
  19. R

    1978 Johnson 75hp compression

    Should be reading about 140 PSI.----So step #1 is a test with another gauge.
  20. R

    1991 Mercury 40HP “Classic” Plug Fouling/Stalling

    There are 2 reed blocks ( AKA bearings ) on the crankshaft parts page.----Easy to find.
Top