Search results

  1. R

    1986 evinrude 28 spl primer solenoid

    A line from the fuel pump goes to the carburetor bowl.----And a line supplies fuel to the primer valve from the fuel pump.-----If that is not so then you know what the problem is.------Sort out the hoses.
  2. R

    1971 evinrude 9.5

    I have seen many of those coils burned through to the magneto plate.---I could get blisters on my fingers or tongue explaining how simple these magnetos are.
  3. R

    1986 evinrude 28 spl primer solenoid

    Do you understand that the fuel that comes from the primer valve goes DIRECTLY into the motor ?----This fuel does not go into the carburetor bowl or through any metering jets.
  4. R

    Rebuilding evinrude 60hp 60073D

    -Make sure that the Florida place ( mastertech ? ) fully understands that you have a 1970 model 3 cylinder 60 HP.----I do not have a lot / any international shipping experience.----I do send out parts locally.---I think I do have some of those bearing kits should they be a stumbling block for you.
  5. R

    1965 6HP Gearcase Not Sealing

    Sorry ----I do not see any damage that would let WATER leak into the gearcase oil.
  6. R

    1973 evinrude 135 starflite

    They sold lots of them but most have been turned into beer cans.----1973 models are unique.----No internal powerhead parts from 72 fit.----No internal parts from 74 fit.----Old motors have different values in certain areas.-----If a local shops will work on older motors they have more...
  7. R

    1986 evinrude 28 spl primer solenoid

    Fact-----If you have to keep pushing the key in then there is an issue with the carburetor.----The primer valve put fuel into the engine.---This fuel bypasses the metering circuits in the carburetor.------Those primer valves are very well made , very reliable.----Likely just needs a new o-ring...
  8. R

    Rebuilding evinrude 60hp 60073D

    Newer pistons can be used.----But wrist pin bearing kits must be used.----Or newer connecting rods can be used.----Here where I am parts are available.
  9. R

    1965 6HP Gearcase Not Sealing

    Someone drilled out a broken screw.----Not from the factory.-----The plate is likely warped and the gasket will leak.----Did you replace shift rod O-ring in 2017 ?
  10. R

    1989 70 hp evinrude won't crank

    Checked the fuse ?
  11. R

    1989 70 hp evinrude won't crank

    Battery voltage is applied to one of the 2 small terminals either C or D.------And one of the small terminals goes to ground.
  12. R

    Lower Outboard

    A manual should be easy to find.-----use google------Old outboard books-----and a few other ideas for a search.
  13. R

    1971 evinrude 9.5

    The MERC-O-TRONIC is just an excellent unit !!-----Will do all the testing on that magneto that could be thought of.----Have 2 of them.
  14. R

    Lower Outboard

    The 1985 model would have a tilt / trim system with 2 hydraulic cylinders and motor / pump clearly visible.
  15. R

    Lower Outboard

    Any idea of the year of the motor ?-----1958 / 59 ------1971-------1991 ----2001 2 stroke or 4 stroke as they are different.
  16. R

    60's/70's Boat Identification

    Hard to tell and at one time there were many local boat builders.----Some are obscure and not well known.----Visit a site called ---fiberglassics-----As they have listings / pictures of many boats.----Might find it there.
  17. R

    1971 evinrude 9.5

    The ---MERC-O-TRONIC ---used a 7.5 volt dry cell battery and 120 volt AC.----There are other ways to get 7.5 volts today.-----This tester is NOT a Mercury outboard tool.-----It simply is a magneto analyzer.----It is very easy to maintain and set up this wonderful magneto to jump a gap of up to 5/16"
  18. R

    Lower Outboard

    Some reading has to be done on your part.------Find an owners manual and read it twice before you turn the key.-----Or pay a shop for 1 hr of their time.----It will save you a lot of beer tokens.
  19. R

    1971 evinrude 9.5

    In my opinion poor starting is usually weak spark.----That universal magneto was first installed in 1950.-----Still installed in the late 1980's.-----Used on 1.5 to 40 HP motors.-----It was engineered to be able to produce 28,000 volts in good condition.-----If it does not jump a gap of 1/4" or...
  20. R

    1971 evinrude 9.5

    Fifty year old motors need a complete evaluation.-----That wonderful / simple / easy to repair magneto needs attention.------This motor needs a new impeller and gearcase inspection as well.----Pull the driveshaft out and have a look at the bearing area above the pinion.----A known weakness is...
Top