Search results

  1. R

    Engine cover (cowling) compatibility for J90VLSIG

    There must be shops around with used ones.----Must be lots on E-BAY too.----Most of the 60 degree V-4 model from 1993 and newer use that cowling I believe.-----90 HP and 115 HP are the same cowling.
  2. R

    Shaft shaft height

    Need to post model # ----Not all V-6 motors are the same !!
  3. R

    1998 90HP Evinrude Problems!

    Told you these are nearly ---" world famous " ----For broken piston rings.----All of the crossflows end up on the overhaul bench !!
  4. R

    1999/2001 50 hp johnson lower unit

    Installing a seal kit is a simple job.
  5. R

    New transom

    I have done 2 of them from the outside.---Just finished rebuilding a transom from the inside too as it was easy to get at.------Some boats are constructed in such a way that going in from the outside is the best easiest way.------You just glue the outside skin back in position for near perfect...
  6. R

    Rebuilding 1985 mercury carburetors

    Most folks pick the carburetor cleaning / rebuild as step #1 for motor fixin.------ Sometimes I say that trouble shooting is becoming a lost art.
  7. R

    Engine cover (cowling) compatibility for J90VLSIG

    Your location ?
  8. R

    Johnson 20R72R

    ??----But there is a shift interlock !----It prevents you from winding this motor up in neutral.----Or maybe the nylon pin at the bottom of the towershaft is broken..----Or the motor is running on one cylinder.----Bring it over as this is easy to figure out.
  9. R

    2 Stroke Yam 40 HP Enduro.-

    Driveshaft is likely broken / sheared and in 2 pieces.
  10. R

    Johnson 20R72R

    Motor has to be in gear for full throttle !
  11. R

    Re-sleeving a 1995 88 SPL Evinrude

    Just bore all cylinder at 0.030"-----If that won't clean it up find a used engine block.------Lots of them around !!
  12. R

    Nothing on key turn

    All electrical connections are under the cowling.
  13. R

    1998 90HP Evinrude Problems!

    Perhaps tomorrow you will realize that removing the one cylinder head needs to be done.----Easy to do.----In the big picture head gaskets are cheap.
  14. R

    Nothing on key turn

    If the solenoid does not click when you PUSH THE KEY in it is not a neutral switch problem.----Check the fuse.
  15. R

    Nothing on key turn

    Test the fuse.----You should hear the primer solenoid click ( item with red lever ) on the motor.----Turn key on and push in , do you hear that click ,yes or no?
  16. R

    Nothing on key turn

    Check the fuse first.---Does primer solenoid work when you push in the key.
  17. R

    Locked down 7.5 Johnson

    Item #21----conical washer----Just above the red circle in the other thread.
  18. R

    What is this repair going to take - hull damage

    The problem is that it appears to have " bonding " issues.------You fix one spot and 6 months later you have the same cracks show up 1' away.
  19. R

    1970 60073D 60hp evinrude

    Available from ----cdi-electronics----US $45.99--Or I have a number of used ones here.-----But you are too far away at this time.-----Have you removed the flywheel to clean the rotor / distributor cap / set the breaker points at 0.010" ?
  20. R

    1993 evinrude 90hp v4 issues

    Orange / blue stripe wires on the top coils ??
Top