Search results

  1. R

    1978 Evinrude 70HP- Trouble starting/idling/bogging under load

    Some " blinking light " spark tester will fool you.
  2. R

    i have 2 mercury 90hp towers 1 is 78 one is 84

    I think it will.
  3. R

    Evinrude 55 1978 gearcase

    Simple job to replace the o-ring in there.-----But I have seen this presenter trying to hammer tapered dowel out of V-4 and a V-6 block.----Trying to POUND them out in the wrong direction.
  4. R

    1978 Evinrude 70HP- Trouble starting/idling/bogging under load

    Just 22 bolts to remove cylinder head.----No timing issues involved.-----Easy on a fresh water motor.----A simple test device is used to check peak output of the electronic magneto.----Buy one for say $10 or make one with wire , cardboard and glue.
  5. R

    1978 Evinrude 70HP- Trouble starting/idling/bogging under load

    Checked thermostat ?----Does spark jump a gap of at least 3/8" on the 3 leads ?---The motor is 45 years old and possibly 5 owners.-----Remove head gasket to inspect cylinders.----Head gasket is cheap compared to ignition parts / carburetor kits or an hr labor at a big shop !
  6. R

    Newbie removing lower end on Mercury 115 4 stroke...

    Just take bolts / nuts off and see if lower unit drops.----Look for possible hidden nut under the trim tab.
  7. R

    Newbie removing lower end on Mercury 115 4 stroke...

    I would not be loosening that.------You may find that the shift shaft is splined and nothing to disconnect.
  8. R

    Yamaha Outboard SLOW crank! Help!

    Take starter apart for inspection.
  9. R

    1978 Evinrude 70HP- Trouble starting/idling/bogging under load

    Compression should be around 140 PSI.-----Load test the battery.
  10. R

    1954 Evinrude 25 - Build Compression, Lose Spark

    Any pictures of this motor and the 3 coils ?----Perhaps some inventive person was trying to modernize this motor ???-----Or a newer motor with an older identification plate???
  11. R

    Evinrude 55 1978 gearcase

    Use a sharp pointy tool.----Remove o-ring.-----Install the new o-ring.-----That hole may spray water into the exhaust for cooling.----Do not fuss over that hole.
  12. R

    omc ignition analizer

    edited
  13. R

    Mercury classic 50 HP - part 2

    None of the Mercury motor inline models have a cylinder head , until they developed the V-6 models
  14. R

    Mecury BlackMax 175Hp, Constant Beep and Overheating

    Blown head gasket can cause overheating.
  15. R

    Ragged out idle 90hp 2 stroke

    ?/---Why would he need 4 carburetor kits on a 3 cylinder engine ?
  16. R

    Mercury classic 50 HP - part 2

    ????----Of course the piston comes out of this engine !----It just comes out in a different way.----This motor must be taken apart.
  17. R

    Fuel system

    If the primer bulb collapses the fuel pump works very well.----Once a motor starts the primer bulb does NOT need to be hard !
  18. R

    Fuel system

    This should be easy to fix.----Test run with a 6 gallon tank and hose.
  19. R

    1954 Evinrude 25 - Build Compression, Lose Spark

    There are 2 coils under the flywheel.-----There is no primary coil.-----This magneto is elegantly simple .---Used on motors from 1.5 to 40 HP.----Installed from 1950 to 1990 models.----You replacement ignition parts are factory original , or something else?
  20. R

    Why o' why?

    ???---Carburetors are but a small issue with motors.----What other trouble shooting has been done if any?
Top