Search results

  1. jimmbo

    Starflite 3 75hp starter issues

    As suggested, drop the lower unit, and see if it still binds up. With the Spark Plugs out, can you see the tops of the Pistons?
  2. jimmbo

    1957 Johnson 35hp overheating

    The Impeller is only one of the Wear Items that make up the Waterpump, the Housing and the Plate below the Impeller are subject to wear too
  3. jimmbo

    boat and trailer sit very low (to my eye)

    You could relocate the Axle to under the Spring, that would increase the Height a bit, or replace the Axle with one that doesn't have the Drop. Added height might result in increased Aggravation at the Boat Ramp though
  4. jimmbo

    De-Winterizing my 1974 Evinrude Lark 50 50472M Engine and no Crank

    A 50hp is small enough to Rope Start with ease.
  5. jimmbo

    boat and trailer sit very low (to my eye)

    Pictures would be Nice. I suspect a lot of people would be happy to have your Trailer, as it makes for easier Launching. I have to lower the Tongue of my trailer as low at it goes, to get enough height at the Back to lower the Outdrive. As for your 250, maybe it, like a lot of Trucks these Days...
  6. jimmbo

    E85 in Chrysler outboard?

    E85 would be a Death Sentence for a Recreational Outboard. They quite often can't even Tolerate the Nasty stuff at 10%. The Fuel System was never engineered for it, and it will make mess of it. Some Racing outboards have used Alcohol, but it takes a lot more Alcohol to make the same amount of...
  7. jimmbo

    88 mariner force 50 hp leaking fuel out exhaust and drain hole

    Welcome to iboats Two strokes do send unburnt Fuel(gas and oil) out the Exhaust, just the Nature of the Beasts. However if it is excessive, then at least one of the Cylinders is running too rich, or is not firing
  8. jimmbo

    Mercury blackmax 150

    The linkages that connect the Throttle shafts on each carb to the other, have to be adjusted so are all closed at the same time. The Sync between the Spark and Throttle Linkage is bit more complicated, and a Factory Service Manual is your best bet there. Any time the Carbs are removed, both sync...
  9. jimmbo

    Starflite 3 fuel pump and other hose routing.

    That would be a 1961 motor http://www.fiberglassics.com/library/images/9/91/Evinrudeservice003.pdf
  10. jimmbo

    Mercury blackmax 150

    Compression, Spark at the proper Time, and Fuel, combined are what makes a Motor run. Start with a Compression Test Does it have Spark good enough to jump a 3/8" gap on every Plug Wire? Fuel... Is fuel getting to all carbs? Are all the carbs synced to each other as well as being synced to the...
  11. jimmbo

    Now what

    Welcome to iboats So start from the Beginning, and what all have you have you done to the motor, trying to get it to run
  12. jimmbo

    service manual

    Used to be oodles of them on e-bay
  13. jimmbo

    Tilt and trim manual release valve

    Welcome to iboats. Do you have a Service Manual, preferably a Factory one? It will have the procedure for Bleeding the System, as well as some troubleshooting procedures. It is possible that the O-rings from your kit are not the correct ones.
  14. jimmbo

    Was running now will not turn over DISTRIBUTOR, TIMING, #1 on CAP & PLUG WIRE LOCATIONS

    Resolution wasn't really good enough to see the Letter/Numbers But you make a Valid Point about if one component is not USCG approved, what else has been replaced and also isn't compliant
  15. jimmbo

    1150 Link & Sync Question

    Are you referring to the Oil Recirculation Lines? Mercury has those in their Parts Lists https://ww2.iboats.com/MERCURY-115-6-CYL/dm/view_id.1702129 part 26 https://ww2.iboats.com/Cylinder-Block-And-Crankcase-Assembly/dm/cart_id.971598793--session_id.900097203--view_id.1702135
  16. jimmbo

    1150 Link & Sync Question

    5/16" was used for all the engines until the V6s(175+hp) were introduced in the mid 70s, in which they got the 3/8" line. Unless you are running a 30' Line the 5/16" is more than adequate. Even at WOT, it will take approx 30 minutes to burn a 5 Gallon(6 US Gal) Tank. A 5/16" hose can syphon it...
  17. jimmbo

    1996 evinrude 48 hp keeps spinning prop hub help!!

    Never heard of that. Perhaps they are also in the Business of selling Clutch Dogs too...
  18. jimmbo

    1957 Johnson 35hp overheating

    You might have to pull the Waterjacket Covers off the Head, the one over the Exhaust Ports , and even the Powerhead off and check for blockage(s). However, first take another look at the Water Pump. Any Scoring of the Housing, and the Plate? Is the Grommet that seals the Pipe to the Pump in good...
  19. jimmbo

    1989/1990 Evinrude 25 hp

    Welcome to iboats Where in Alberta?
  20. jimmbo

    Need help with year and horsepower of this motor , Can someone please help me ?

    What's with the Front cover from an Inline 6? That V6 has been apart, the bolts holding the Crankcase together look like an Impact was used on them It is definitely a bunch of Pieces cobbled together. Cowl is from an 84/85 Has no Choke, post 79? Second Generation Transom Bracket. Possibly a...
Top