Search results

  1. massimofinance

    my brand new VHF handheld does not work

    I bought a Standard Horizons HX 370S at West Marine, went down to the shore, and tried it out. I get the weather no matter where I am (even in the house, miles from the shore) but nothing else. I turn the squelch down to 00 (per the manual) then start up until the noise clears, which is...
  2. massimofinance

    Can I use Thomson's watersealer to waterproof my bimini top?

    Can I use Thomson's watersealer to waterproof my bimini top?<br /><br />Thanks,<br /><br />MAX
  3. massimofinance

    Should me temp sensor have power?

    On an Evinrude 115HP, should the brown wire that goes from both tempature sensors to the big red plug have power when I turn the switch? I just rebuilt the motor, and worry that it is over heating, (which could be the reason the old owner ruined his pistons) I take a test light to that wire...
  4. massimofinance

    Citizen's band radio instead of VHF?

    I will always be boating in Long Island Sound, am already over budget with the boat and I have a cell phone. Would like to skip the VHF radio and just keep the CB radion (with antenna) in the boat, for an emergency. What do you all think? Waste of space/weight? I know the consensus will be...
  5. massimofinance

    Garmin bluecharts

    Anyone try to get a blank Garmin data card and load their own bluecharts onto it?
  6. massimofinance

    Does an outboard need to have water running through it to start?

    I just rebuilt my 110HP 82 Evinrude O/B. When I try to turn it over, it does not start. I went through JB's "engine does not start" FAQ's (really good materials, JB!) and the motor is fine. I checked the carbs, starter, fuel pump, everything, and had a boat mechanic come to the house, and...
  7. massimofinance

    Why won't the motor start?

    I rebuilt the top end and bottom end and tilt system on my 1982 115HP Evinrude outboard. I turn the key, the starter spins, not fast and constant, but slowly and intermittantly. The motor does not start. There is a fuel pump with a nozzle on top that squirts gas out when I press the key in...
  8. massimofinance

    What Oil do I need to mix with my gas?

    Hi all, wanted to find out what oil I should get to mix with the gas for my 1982 two stroke Evinrude 115HP. Also, what is the mix ratio? Also, I need to use lower octane gas, correct?<br /><br />Thanks,<br /><br />MAX
  9. massimofinance

    Propeller is chipped

    Hi all, the Prop on my Evinrude 115HP has a few chips, no more than three, total an inch long, by 1/8" deep in one of the vents. Do I need to replace the entire thing? If I do not, should I file them down so that it is a smooth line?<br /><br />Thanks<br /><br />MAX
  10. massimofinance

    Does my engine need to be running?

    First off, I want to thank all of you for always answering my questions right away; this is a great resource for a newbie like me!<br /><br />Second, I rebuilt my power head (1982 Evinrude 115HP VRO) put it back on top of the motor, connected all the wires, and when I put in the key and try the...
  11. massimofinance

    Does my engine need to be running?

    First off, I want to thank all of you for always answering my questions right away; this is a great resource for a newbie like me!<br /><br />Second, I rebuilt my power head (1982 Evinrude 115HP VRO) put it back on top of the motor, connected all the wires, and when I put in the key and try the...
  12. massimofinance

    registering a trailer and need some weight information

    Hi all: I need to register a trailer (old) and I have no information on it. I need the following for the registration forms for Vermont:<br /><br />1) empty weight, and<br />2) weight of trailer and load.<br /><br /><br />The trailer came with my 1984 16' bayliner capri. the trailer is...
  13. massimofinance

    Tightening torque for crankcase cover

    Hello, I have an 82 Evinrude 115 HP V4, can anyone help me with the torque # for the four inside bolts that are tightened using a hex key? Thanks.
  14. massimofinance

    owner's manual for 86 bayliner capri same as 85 capri?

    Sorry if this is the wrong spot, but will the owner's manual for an 1986 Bayliner Capri 1600 be the same for a 1985 Bayliner Capri 1600? <br /><br />Thanks.
  15. massimofinance

    Connecting Rod Screws: How Tight?

    1982 Evinrude 115HP 2-stroke, VR-4, VRO<br /><br />The book says 30-32 ft-lb, I started at 20, and the torque wrench is clicking, but there is no way I feel comfortable going higher. Any advice? <br /> <br />The book (Clymer's) says 1985-on 120-140 HP is 42-44, and 1986-on 200-225 HP 42-44, then...
  16. massimofinance

    What Horse power kicker should I get?

    I want to get a kicker for my 85 16' bayliner capri, does anyone have recomendations for size, type, etc.? Thanks!
  17. massimofinance

    115 HP V4 E-rude crankshaft question

    Hi all, happy thanksgiving!<br /><br />I have a question about my crankshaft. In the middle of the crank shaft, I see there are two small holes. The crank shaft is still mounted in the head. Which direction should these holes be facing? should I turn them in, so I do not see them anymore, or...
  18. massimofinance

    How do I know what prop is for my engine?

    Hi all: I am rebuilding my 1982 115HP Evinrude VRO V4 outboard. The old owner (a friend) told me that the prop that is on the outboard is not the one that came with the engine. I am thinking this is why the engine overheated and led to the work I just did. How do I figure out that size prop...
  19. massimofinance

    Painting my Evinrude cover

    I am completely repainting my cover. I sanded it a bit, taking the chipped pieces down, and sanding all the rest (not down to the bare plastis, though the plastics is showing in some areas). Do I need to buy some Evinrude grey paint, or is there an off the shelf counter part? Any help in...
  20. massimofinance

    How do I properly torque the bolts?

    I am rebuilding my 115HP Evinrude, and have to tighten the bolts for the Cylinder Head and the connecting rod cap. The book says 18-20 FT/LBS for the head, but when I set my torque wrench (automotive) to some place below 20 (it starts at 20) It is tight and I am careful to not blow the bolt out...
Top