Search results

  1. R

    What would cause my FSK16 to not be propelled by my Johnson JW10 3hp?

    See post #3----Shear pins are usualy 3 pieces when an incident has occurred
  2. R

    1995 Johnson J6REOD WOT issue

    Checked reed valves ?----Any pieces broken on the throttle cam?----Throttle plate going full open ?
  3. R

    1964 9.5 evinrude

    What is " everything " on this motor.----Help yourself and post exact details.----Did you run it with 50:1 gas oil mix, yes or no ?
  4. R

    50 hp high speed misfire

    The timing on these motors rarely goes out of adjustment.---Well a sheared flywheel key throws timing out.----And no you can not find a sheared key condition with a timing light.---Well , at least not on most motors.
  5. R

    50 hp high speed misfire

    Set idle RPM with boat in the lake.----Warmed up and in gear.---Testing in a bucket with no prop is a waste of time.
  6. R

    1964 9.5 evinrude

    It appears to be scrap now.----Just 12 cents / lb-----Not what you want to hear but it is " world class " advice from people who know the facts.
  7. R

    Prop pitch for 150xp crossflow on pontoon

    There are lots of toons with monster motors.
  8. R

    Add telltale pee hole to 1965 Johnson 75 HP

    The exhaust relief on a V-4 75 HP in 1965 is a better item than a tell tale on many modern motors !------At full throttle water pours out of there.----Then when you slow down the hot water / water vapor pours out until thermostat controls temperature and water just spits out.--Tell you all is...
  9. R

    Water Separator , larger filter verses smaller filter

    If boat is left in the water use a large filter.----If it lives in the driveway a smaller filter will do.
  10. R

    1964 9.5 evinrude

    My guess is that you have never seen a cylinder wall of a " new condition " motor.----Your motor needs to come apart.----Needs to be bored and oversize pistons fitted.---Returned to new factory fit and finish.-----I doubt you can find these parts today.----Find good used parts on E-bay...
  11. R

    1964 9.5 evinrude

    Sometimes it is hard for folks to accept the truth from people who have worked on many of these motors since 1968.----Have all kinds of parts for those motors.----Boxes full of good parts.
  12. R

    1964 9.5 evinrude

    The motor appears to have been run on straight gas and no oil oil the mix..---It is JUNK now.----Beyond economical repair.
  13. R

    1964 9.5 evinrude

    The pictures now show what I suspected.----Motor needs to come apart for a rebuild.---Simple as that.---It is JUNK.
  14. R

    1964 9.5 evinrude

    Good luck with your motor.---You have in under control.
  15. R

    1963 Evinrude Mate 2 hp impeller

    I only use factory impellers.----Not worth trying to save a few $$ on a critical part.
  16. R

    1964 9.5 evinrude

    Out of focus and does not show fine detail.---Try again.
  17. R

    1963 Evinrude Mate 2 hp impeller

    That impeller or the improved water pump kit should be in stock at most BRP ( Evinrude ) shops.----That is if you can find one.----In Canada---evinrudeparts.ca----Is one source.
  18. R

    Yamaha 90 hp 2 stroke

    Time to take it apart for inspection.-----Used parts might be available.-----Your location ?
  19. R

    1964 9.5 evinrude

    Post more pictures of the bottom cylinder wall.----Does not look good to me.
  20. R

    1964 9.5 evinrude

    Water must be 8" above impelle in your test bucket.-----Give some details as to what is " new " on this motor !!
Top