Search results

  1. R

    Johnson 70EL76D Looper Terminal Block Wiring

    There is no ECU on a 1976 model.-----There is no " limp mode " on a 1976 model 70 HP !!
  2. R

    1940s 4 Cycle Flathead Opposed Mystery

    Post some more pictures.
  3. R

    1989 Evinrude 88SPL (E88MSLCER) Cooling

    Yes they carry water !!-----It should be easy to see how the water gets in there !!----Water does not go through that cover gasket !
  4. R

    Johnson 70EL76D Looper Terminal Block Wiring

    Well ----I cannot see , feel or touch your boat.-----I can only try to educate / teach those who are willing to listen.----The factory control had a waning buzzer !!----And compression should be around 140 PSI.----I will step aside.----Good luck with your project.-----Note ---I started repairing...
  5. R

    1963 Evinrude won’t start

    I say it all the time.----This simple magneto was installed from 1950 to 1990 om motors from 1.5 HP tp 40 HP.---Easy to maintain in any garage or backyard !
  6. R

    1989 Evinrude 88SPL (E88MSLCER) Cooling

    Is there a channel / port in the bottom and top of the head??-------And remember they made this cylinder head from about 1973 to 1998.----I think these folks knew how to build elegantly simple motors !!
  7. R

    Johnson 70EL76D Looper Terminal Block Wiring

    Just learn to test the overheat horn !!----If you have no clue ask.----There was a horn installed in the control box when that fine motor left the factory.----That is why I suggested to test this horn !
  8. R

    1989 Evinrude 88SPL (E88MSLCER) Cooling

    Take a really good look at the cylinder head / head gasket and see how water flows.-----Hint----The water flows towards the hose outlet and then to the thermostat.
  9. R

    Rkl-29e wont go forward

    I have the factory tool kit for these.----But I think a !/4" ( fine thread ? ) threaded rod and slide hammer can be used.---Work carefully
  10. R

    Johnson 70EL76D Looper Terminal Block Wiring

    Terminal 2 and 3 are the same connection.----Clearly seen in your picture !!-----But post your actual compression values here.----And is a new water pump impeller installed every 5 years ?-----Tested the overheat horn ?
  11. R

    oil intake adjustment

    Explain why you mention----" oil intake adjustment " on this motor ?-----You would have to replace the carburetor jets.----Fairly easy to do.----Your location ?
  12. R

    Help Me Identify Old Super Sea Horse

    RK is for electric shift.----This motor is NOT electric shift.
  13. R

    Trying to find a suitable engine

    If you do not like affordable older motors then visit a showroom.----Tell them what you want and present the credit card.----I would go with an older 6 / 8 HP Mercury.----Avalable with electric start and kits for remote operation.
  14. R

    1955 evinrude 7.5 hp carb and starting

    Love seeing pictures of those old ignition coils.----Have a bunch on hand here.-----Sometimes it is difficult to explain the difference between spark on a plug and maximum output of one these simple magnetos !!
  15. R

    1973 Johnson 9.5hp Motor Troubleshooting

    Remove bottom coil , it is possible that insulation failed.----Look for " burn through " between coil and magneto plate.----Voltage would rather take the easy path to ground rather than jump gap at the plug.-----Do not have enough fingers and toes to count how many times I have seen that !
  16. R

    1973 Johnson 9.5hp Motor Troubleshooting

    The 1/4" or more gap jump puts the magneto and components to a full test.-----Most are unaware that it takes more voltage to fire a plug when air is compressed to 100 PSI----So a plug that sparks touching the block will not fire in the cylinder.----That makes you think you have spark and keep...
  17. R

    1988 XP150 Overheat alarm

    Some might argue.----Fact is that water from the tell tale does NOT circulate through the block.-----It indicates that water pump is working.----There likely is internal blockage.-----Remove cylinder heads.-----Look for ' water diverters " as they guide water around the block.-----Remove water...
  18. R

    Rkl-29e wont go forward

    Sounds like there may be a broken wire going to or at the forward magnet.---For me it would be an easy investigation / fix.----Not sure of the contents ( tools ) in your work shop.
  19. R

    1955 evinrude 7.5 hp carb and starting

    Those are the reed valves.-----They do not move very much ( impossible to see _ when turning flywheel by hand.----Does spark jump a gap of 1/4" or more on a test device , yes , no or no idea why that test is important ?
  20. R

    1973 Johnson 9.5hp Motor Troubleshooting

    No it can not be the issue.----Does spark jump a gap of 1/4" or more on both leads , yes or no ?
Top