Search results

  1. R

    Lower end 2003 75 hp Mercury

    The impeller puts lots of drag on the driveshaft.
  2. R

    Lower end 2003 75 hp Mercury

    Generally you need lower unit and control the same.----So try lever in neutral.----And put lower unit in neutral.
  3. R

    Johnson 140 Sputters at Full Throttle

    Hook up a timing light.----Just 1 cylinder at a time.----See how spark behaved as you throttle up.----Just observe the flashing light.
  4. R

    1956 5 hp Gale Buccaneer

    Sounds right.------Post picture of this motor.-----Be easy to identify it.-----If it was built by OMC then many Johnson parts fit.
  5. R

    Intermittent Start - Starflite 75

    You might need a new impeller now.-----Is the belt timing correct?
  6. R

    Mercury XR6 150

    Compression test.----Post actual values here.-----Does spark jump a gap of 3/8" on all leads ?
  7. R

    I need help with a 58 super thunderbolt iekhaefer!

    Unscrew that round knob on the front.
  8. R

    Mariner 45hp Carburetor Leaking after Total Rebuild....stumped!

    Post compression test actual values here.-----Water pump impeller replaced ?----Checked exhaust tuner for blockage.----Reed valves checked ?
  9. R

    Sealant for Gas Tank Gasket

    Those 2 wee pins are valves.-----When hose is attached to the tank they open.-----One lets gas out.----One lets air in.-----There are 2 o-rings inside the housing and 1 o-ring where a pin comes through .----Simple to maintain.----I used to do that for folks at a dealer when I worked for $1.50 /...
  10. R

    74 stringer electric shift rebuild

    It is NOT a shear pin.----It is a steel drive pin.------The factory props on these are NOT one piece and solid !!----There is a rubber drive " slip clutch " in them.
  11. R

    Need Help with Ignition

    Many folks are not aware that outboards need a new impeller about every 5 years.----If it overheated , a compression test is a good idea.----Post the numbers here.
  12. R

    Is there a guide to removing the powerhead on a 93 to 07 9.9

    Remove lower cowlings.----Remove bolts / pins / links / hoses as needed.----Repeat until powerhead is off.
  13. R

    1993 Evinrude 30 HP tiller pull start

    Same part from other motors fits.-----Is it the sheave that is KAPUT or the recoil housing.-----If in Canada try----evinrudeparts.ca----
  14. R

    74 stringer electric shift rebuild

    ?????-----There is a hub in those props !!!!-----Even with regular gear oil the spring will not slip.-----That is if the spring and hub are in good condition.---Spring and hub can slip with correct oil in the unit.-----Mark the prop and hub.----Test run.-----This is all so easy to check out !!
  15. R

    Grady transom repair

    I am using composite hockey sticks ( carbon fibre / graphite ) for a transom repair.----Very strong and light weight as they are hollow.----Do not taste like wood and will not rot.
  16. R

    1998 Johnson 115 Prop Shaft Seal Replacement

    Small pry bar or hefty screwdriver works-----Pry in an area with backing to prevent damage to bearing carrier.
  17. R

    1800 fisherman transom problem

    They likely fixed it 10 years ago.----Yes ,---if you are paying someone for this simple work it adds up fast !!!
  18. R

    74 stringer electric shift rebuild

    Try another prop first.-----I think the hub is slipping.-----If it is the drive spring slipping the lower unit must come apart for inspection.----Mark the prop and prop hub.----Test run and see if marks moved.
  19. R

    1998 Johnson 115 Prop Shaft Seal Replacement

    Remove 2 bolts #28 and pull out item #24.-----install new seal and item #17.-----Install a new water pump impeller as well.
  20. R

    E15REOD idle

    The high speed jet is not anywhere near plug #17.
Top