Search results

  1. C

    Gas Pressure washer "turn off" instructions incorrect??

    Gee, I put a short garden hose (washing machine hose) on the pump, stick a funnel into the upper end and dump in some windshield washer fluid. After it stops draining, I blow some compressed air into the hose, blowing out any water and fluid. I cover and store it outside.
  2. C

    Transom bolt pattern for older (1983) 50HP 4 cyl Mercury with power tilt and trim

    Gee, how about some 1 or 1.5 inch lumber spacers to allow clearance for the cylinders. S/b under $10 I would think.
  3. C

    96 Mariner Magnum 3, 150hp: Quick Help

    Sorry, I do know understand your last post. As far as I know you, and a guess at your question, you need the flusher device to flush the motor. The cap on the engine oil reservoir is to refill it, if it is low. Not all motors had the in-boat reservoir, and sometimes the reservoir refill...
  4. C

    Transom bolt pattern for older (1983) 50HP 4 cyl Mercury with power tilt and trim

    If you plan on a trip up a shallow river, you will need a way to trim the motor. My Jackplate was a 2 piece kind. Basically on each side, there was 2 aluminum angle irons bolted together. A bolt on each allowed for up/down adjustment. The width of the Jackplate allowed me to mount my '77...
  5. C

    96 Mariner Magnum 3, 150hp: Quick Help

    Gee, thread is still open. Merc V6 engines have an oil reservoir on the engine, and can also have one in the bilge. Engine crankcase pressure forces the bilge reservoir to refill the engine reservoir continuously. The engine oil reservoir is gravity feed to the oil pump. Low speed (<2000RPM)...
  6. C

    1996 Evinrude 115 fuel hose routing

    Here is a parts list. I am not sure if the model is exactly the same but should be close. I am not sure if it will help though. I have a motor similar to yours, but unfortunately, I have never needed to work on the primer, and the boat is well covered for the winter. Hopefully someone has...
  7. C

    Transom bolt pattern for older (1983) 50HP 4 cyl Mercury with power tilt and trim

    Your Merc and it's PTT system should use 6 3/8" bolts. One in each of the lower "arms" of the transom bracket and 2 on each PTT bracket. The bolt pattern is different from the BIA standard, but I was able to mount it to a Jackplate, with some new drilled holes. Remember, when trimmed, the PTT...
  8. C

    Spinning reels

    Gee, only my newest Ugly Stik has SS guides. I suppose all the other OEMs could have converted in the last 5 years or so, but my suite of fishing rods is older, and definitely do not have SS guides.
  9. C

    ‘91 merc 60hp overheating alarm buzzing

    Compression and leakdown tests can tell the condition of the cylinders and pistons.
  10. C

    How do I drain my fuel line?

    Two ways to do it. One is to remove the fitting at the motor end and pump the primer bulb. Second is to stick a small screwdriver into the motor end fitting and push the chrome ball back against it's spring. Now pump the primer. Be careful not to tear the rubber seal that touches the ball.
  11. C

    Spinning reels

    Ugly Stik rods and Penn reels are good quality. Penn reels has a nationwide chain of places to get parts, if you break something. I have never broken an Ugly Stik rod, unlike some Garcia's, Daiwa's and others. Newer Ugly Stiks have SS guides, which are nice here in salt water. Some years...
  12. C

    Should I use a kicker when trolling in a 4.3L Mercruiser?

    To add to what Lou said. In saltwater use, any steel parts are vunerable to corrosion. On my '88 4.3LX, I used to find bits odd black-painted rusty metal in the bilge every once in a while. Some were part of the flywheel cover, some were unknown. I also had to remove the circulating pump...
  13. C

    1988 Mercury 90 RPM Issue

    Mercury motors often have high and low speed stator windings. If the high speed stator windings went bad, RPM will be limited. You might ohm them out.
  14. C

    ‘91 merc 60hp overheating alarm buzzing

    When installing a new impeller, inspect the bottom of the old one. Look for damage there, which has been often known to lead to overheat at idle. I would also inspect/replace the thermostat, as that controls cooling at slow speeds. High speed cooling is controlled by the poppit valve.
  15. C

    Brake based limited slip differentials

    The way I understand the "Posi-traction" limited slip differentials of the 70s and 80s, was that they often had mechanical breaking on the wheel that slips.
  16. C

    Winterizing, use E-0 stabilized gas or install shut off valve and run carb out of fuel?

    Gee, I have never had an issue with E10. It keeps the fuel system clean, and eliminates water in the fuel, or really cuts it down. My water separators have an oz of water or less in them at the end of the season. I only change them when they start to rust on the outside. On multicarb OB...
  17. C

    Yamaha lower unit stuck

    Gee, stuck how? Stuck on, stuck in gear, stuck in the mud, trim stuck down? What year and model?
  18. C

    Gonna need to pull my Alpha outdrive, no water flow.Thinking its clogged

    Charlie, I have had the water passage under the waterpump in the OD, nearly clog with barnacles. A lot of Alphas have removeable gratings for water intake. You can pull 'em off and take a look.
  19. C

    Aftermarket Mercruiser parts, What are you using???

    On my MerCruiser, I would routinely use automotive fan belts which were $10 vs $70 for Quicksilver ones. I also matched auto U joints (less than $10 ea) vs the Quicksilver ones at $50ea. For non-DIYs, using Quicksilver parts can make some sense, as they may (may) last longer, and installation...
  20. C

    Water in bilge

    Gee, water is 8 pounds per gallon. Why not add 200 gallons of water to your boat on the trailer? What could go wrong?
Top