Search results

  1. alldodge

    2002 5,7 Mercruiser exhaust manifold keeps cracking - 5 times this summer

    Never seen a set of injectors that were exactly matched to one another, even brand new, but then again they were not flow tested
  2. alldodge

    Mercruiser 5.7mpi horizon single cylinder burning lean

    With Pics working again, can you post the plug? It could be while running a tad lean, might not be enough to worry about
  3. alldodge

    Bravo 3 outdrive overhaul - propeller shaft seal questions

    New seals 1 each Small inner seal 26-8M0033407 (replaces 2 each lip seals) 1 each Large outer seal 26-861694 (replaces 2 each lip seals) Dimensions 3 - 3/8 OD, 2 - 1/2 ID, 13/16 wide Use manual 28 and on page 3D-26 it list removal tool as 91-862064A1 If you do not have the manual, then need to...
  4. alldodge

    Bravo 3 outdrive overhaul - propeller shaft seal questions

    Welcome To remove prop shaft both carrier and retainer must be removed. As mentioned in my thread I tried the slide hammer and was not able to get it out. I wound up splitting the seal to remove. Figured I would buy the correct tool and use a press if I needed to do it again Didn't have much...
  5. alldodge

    Mercruiser 4.3L - ignition fuse blowing

    5A being small look for another low current item Also is there another bilge pump
  6. alldodge

    2002 5,7 Mercruiser exhaust manifold keeps cracking - 5 times this summer

    ok, if you can see the crack then don't bother with testing
  7. alldodge

    Upholstery Decals falling off.

    Welcome Would suggest a vinyl type glue
  8. alldodge

    Mercruiser 4.3L - ignition fuse blowing

    Welcome Being 5A fuse and it blowing now after a heavy rain it's probably the bilge pump. Is there water in the bilge?
  9. alldodge

    1978 Johnson 150 hp tach wire

    Moved to Johnson, maybe get some other eyes on it
  10. alldodge

    High Altitude prop question.

    Welcome What ever prop your using now find one the has 2 inches of less pitch then current. Exp: 19P go with 17P
  11. alldodge

    Intake Manifold Gasket Leak: Need Help Sealing

    Welcome The stuff in your link is basically radiator stop leak Folks have tried to use that kind of stuff for years. It coats everything in the motor and does stop a very small leak, the issue is it doesn't last. The other thing is it won't do a head gasket
  12. alldodge

    2002 5,7 Mercruiser exhaust manifold keeps cracking - 5 times this summer

    We thought all were verified cracked in same place Can test by using a piece of rubber and sandwich the elbow and manifold together, or use a piece of flat steel or even a 2x6 piece of wood. Then pressurize to 1 bar
  13. alldodge

    1973 Gibson help

    There is an impeller inside Look for a thru hull shutoff valve and close it. Then remove the pump and disassemble Does look like the G7B and if correct look for rebuild kit If pump needs complete rebuild with bearings I found this one Rebuild
  14. alldodge

    SEI preload and a stern jack

    Oh and when your turning the boat, you can reach over the side and in about 6 inches feel the water
  15. alldodge

    SEI preload and a stern jack

    Don't know how much if any. Boat was bought from Checkmate in 85 by my Buddies brother who is a doctor. The same model never came with a 383 so no numbers +/-. I've been in it and speed-o does not keep up and it doesn't have a GPS. Pics of it on the water with 4 people in it, all you see a WOT...
  16. alldodge

    SEI preload and a stern jack

    1985 Checkmate with custom 383
  17. alldodge

    SEI preload and a stern jack

    Pics Imagine trying to put that short yoke into the back side of the stern jack and it's attached to a drive.
  18. alldodge

    2002 5,7 Mercruiser exhaust manifold keeps cracking - 5 times this summer

    Connect clear hose to other end of hose prior to elbow
  19. alldodge

    No fuel at rail with KO/EO merc 350 mag mpi tow sport (02 centurion)

    Think of a garden hose, the water comes from the house (the pump). The spray nozzle (regulator) regulates the pressure based on how much nozzle is opened or closed The high pressure fuel pump will produce more then 60 psi. Can bench test fuel pump on bench with gauge connected direct to pump...
  20. alldodge

    1973 Gibson help

    Look at thread below, and in post 4 there are some pics and the pump has been removed and laying in front https://www.marineengine.com/boat-forum/threads/newbie-question-are-any-differences-between-chrysler-nissan-diesel-sd33-and-patrol-160-series-sd33.421902/
Top