Search results

  1. A

    Are wheel locks the way to go?

    Just had another idea...paint it camoflage then no one will see it !!
  2. A

    Are wheel locks the way to go?

    Might very well work!!!
  3. A

    9.9 HP mercury O/B Starter cable

    Good to hear...
  4. A

    Bilge pump wiring mystery

    Shows how old I am......mine always had float switches....what will they think of next??
  5. A

    Are wheel locks the way to go?

    LOL....all depends on whether you are raised in the country or in the city !!
  6. A

    Making a kicker motor steering addition

    Yes, I use a small 2.2 hp gas for foward thrust, locked straight ahead. Then my 55 lb thrust trolling motor has autopilot and remote steering so I can pay attention to my rods and fish. Troller is controlled by a remote hanging around my neck. Works great....can tell it what course to take or...
  7. A

    Optimized prop for Lund Fury 1625 XL w/60hp Bigfoot

    Oh wow...Didnt realize the wot was that high !! Especially these newer 4 strokes... I stand corrected...
  8. A

    1986 75hp Mercury 4cyl shop manual

    I have a 1992 40 hp model , I found a used factory service manual on Ebay for inly 20 bucks. Nice thing to have, makes servicing these motors much easier, just make sure you get a " factory" manual and not a generic
  9. A

    1989 Mariner 20HP

    We have all done dumb things, that is how we learn !!! Glad you were able to find your issue.....
  10. A

    9.9 HP mercury O/B Starter cable

    Mabey to much grease causing them to hang up and not engage ? Clean them good and see what happens, if full of crud, then clean and light lube.
  11. A

    Bilge pump wiring mystery

    Is the float switch in a position where you can reach and manually lift it up and down ?? If so you can test the auto mode without water....
  12. A

    Where is Depth Finder transducer located

    With a great deal of difficulty.......why they do that makes no sense to me...I guess that is why most boats go to a transom mount
  13. A

    Optimized prop for Lund Fury 1625 XL w/60hp Bigfoot

    You or anyone else would be guessing right now, so why not wait until you can get precise weight and rpm readings ?? I can tell you one thing....that motor wont last long at 5700 rpm....
  14. A

    same speed with different props

    That co pilot seat sure looks comfy !!!
  15. A

    Part Identification

    From what I can see, it appears you have somevserious corrosion issues on that tank. I would drain and remove it, if it were my boat...does not appear to be safe, fuel leaks and fires do not go well in boats !!!!
  16. A

    Bimini top advice needed

    They are easy to set up and down in my opinion, never had an issue. Foldvthem back and slip on a boot and it all stays nice and neat. Boot takes longer to install than folding the bimini !! Now, with that said....if you do a lot of standing, then they are great, but if you sit a lot, the...
  17. A

    Are wheel locks the way to go?

    Yes, but look at the quality of the locks, I could probably do that as well. I will put up a hondo if someone can pick my locks in less than 15 seconds !! Wont say it cant be picked, but it will take some serious tools that only a few crooks would carry. If youvwant good quality serious...
  18. A

    Making a kicker motor steering addition

    I lock my kicker motor straight ahead, then use my bow mount trolling motor to steer, it has remote steering and autopilot so controling is a breeze.
  19. A

    1997 20HP Evinrude E20CREUM Owners manual?

    Cant get anything on that site to open up, just says try reloading over and over.. Any suggestions??
  20. A

    Anti-Rattle solutions

    The only issue for me is...I remove my draw bar after every outing, to much of a pain to go thru that each time I use my trailer. I prefer making the required adjustments to my hitch to stop the rattles....to each his own, but once I have mine fixed, just pull the pin or install the pin and go.
Top