Search results

  1. Lou C

    Just acquired a 170 Horizon. Assembly required.

    boat looks great and you look like you're having fun! Here's ours, it sits on a salt water mooring so I can't keep it as clean as most here can who trailer and bottom paint is a necessary evil. But, I don't have the hassles of trailering, only 2x a year and if a storm runs up the eastern...
  2. Lou C

    Steering actuator vibration

    That's interesing! What may be happening is that when it starts in the first vid the engine is running rough shaking side to side, that might be causing the steering arm to move in the transom assembly which via the steering cable would move the shuttle valve in the steering actuator causing...
  3. Lou C

    Starter issue, possibly water related

    If your motor is cranking (turning over) fast enough to start but no start your starter may be ok, for now at least but you may have gotten water in the distributor. Salt or fresh water? If salt and water got over the starter just go buy a new one now. If fresh if you dry it out it may still work
  4. Lou C

    Mercruiser 6.2l 300 (2018 model) Gimbal bearing grease how to?

    Or the prop shaft for run out. Any prop strikes?
  5. Lou C

    Mercruiser 6.2l 300 (2018 model) Gimbal bearing grease how to?

    The newer Mercs have permanently lubed gimble bearings & ujoints so you can’t grease em. The main thing is regular drive pulls to check for water in the bellows. Keep water out & they will last If you can’t get at the zerk fitting due to engine installation the only way to ensure proper...
  6. Lou C

    5.7 omc stalling while shifting

    Sounds good, you’re going with a 15x13 prop right? You want at least 4500 rpm with wide open throttle trimmed properly.
  7. Lou C

    Power steering , worse when running

    Nice feed back, and good to know
  8. Lou C

    4 flat 7 wire trailer connector

    I used the Hopkins quick connect to make a spare extension harness and just soldered the wires to the terminals instead of depending on friction to hold them…
  9. Lou C

    Starter bolts for 99 model3.0 cobra Volvo penta

    I know Arco sells an installation kit with the bolts, but it depends on the starter you have. Bolts that are too long can let the starter to shift & can break the bolts off in the block. Make sure they do not bottom out before clamping the starter tight!
  10. Lou C

    Wrong Exhaust Manifold!

    If you don’t want to pay for Merc OE then try Barr Marine aftermarket. I used em on my center riser conversion & it worked out great. No leaks fit like factory.
  11. Lou C

    Wrong Exhaust Manifold!

    The dry joint is a better albeit more expensive system. I’d go with that for sure!
  12. Lou C

    5.7 omc stalling while shifting

    Not really but if the centrifugal advance in the distributor isn’t working that could do it. Sometimes it’s a combination of problems causing a problem like that
  13. Lou C

    OMC 5.7. Totally frustrated

    You should really set the dwell with a meter, I use a remote starter switch with the cap off and that is faster. Set dwell, set timing and set idle in that order. idle is a little high, 630 rpm
  14. Lou C

    5.7 omc stalling while shifting

    well now that you know how to adjust it you can retard it slightly and see if that affects that noise, like from 8*-->6* see if that helps. The issue is the more you retard it the more power you lose. So I run mine right at the spec of 6* for the 4.3 and run high octane gas. A lot of people...
  15. Lou C

    5.7 omc stalling while shifting

    You might want to get a mechanics stethoscope they are great for tracking down noises
  16. Lou C

    Bad Experience with Mercury and Bass Pro.....

    did they register the warrantee with Mercury? that's what I'd want to know right away we bought a Suzuki DF 2.5 from a dealer and the trouble we did have was covered under warrantee.
  17. Lou C

    5.7 omc stalling while shifting

    check fuel mixture, inspect spark plugs look at center electrode insulator, are they blistered white, if so fuel mix may be too lean I would also check total timing advance. Use premium gas no matter what it says in the manual What is your engine temp? Should be 160-175
  18. Lou C

    5.7 omc stalling while shifting

    Right and if you hear a ticking noise it could be pinging which isn’t good. Might have to adjust fuel mixture & make sure the accelerator pump is working. Fuel mix might be too lean. I use at least 89 and at the gas dock they only sell 93 octane. I know the marine engine companies say 87 is ok...
  19. Lou C

    94 Cobia 5.7 Chevy/Yamaha setup

    No way. No parts no support no deal
  20. Lou C

    5.7 omc stalling while shifting

    Try the 15x13 & see what you get
Top