Search results

  1. Scott Danforth

    Need Help Installing Distributor in 4.3MPI

    Start with rotor at bottom notch (at 7 oclock), as you drop it in, it will spin around to notch at 3 oclock. May have to spin motor to get dizzy to drop into pump shaft
  2. Scott Danforth

    5.7L 1984, Rough idle at start up, then ok after a minute or so

    I would test the sensor prior to throwing money at it.
  3. Scott Danforth

    Car won’t start. One click

    after all the connections are clean, shiny and your MIL can eat off them...... then seal them with marine electrical varnish
  4. Scott Danforth

    Another winterization question

    if you have power steering, you have a power steering cooler...... always.
  5. Scott Danforth

    Carpet question 1990 Searay 180BR

    you can call customer service at SeaRay, they may be able to tell you a color and manufacturer
  6. Scott Danforth

    Transom replacement on I/O

    only way to check is test drill if the shavings are light-colored, dry and smell like fresh cut wood, you are good to go if the shavings are dark-colored, wet and smell like rotten mulch, you cut out the floor
  7. Scott Danforth

    Transom replacement on I/O

    because replacing stringers and transom is structural work. if you do not properly support the hull, you could end up with a hook in the hull
  8. Scott Danforth

    Electric Boats

    I have run out of fuel no less than 20 times, usually when stuck in traffic for hours. Then again, in the same traffic jam, there are usually 2-3 teslas on the side of the road too. mechanical problems - about 20 over the past 30 years (broken crank, broken rod, bad bearings, wheel bearing...
  9. Scott Danforth

    Fuel Problem

    there is no mechanic in a can seafoam can not unclog your carburetor
  10. Scott Danforth

    Transom replacement on I/O

    dont be surprised if you find that the stringers are gone too. pull the drive, pull the motor, make a cradle start removing rot with the tools of descruction
  11. Scott Danforth

    Repairing Foam Filled Stringers

    its best if the foam can attach to the fiberglass. the strength is as a composite member. by putting in the strips of foam, first, it will dissolve a bit, however it will not be adhered to the inside of the fiberglass. so you will be promoting cracking vs resisting cracking
  12. Scott Danforth

    Transom replacement on I/O

    All of it. Its one big piece
  13. Scott Danforth

    Woke up this morning with a tree on the boat

    Fire up the tig welder and reweld
  14. Scott Danforth

    Don S Winterization link not working

    Yearly drive removal for inspection
  15. Scott Danforth

    Overweight motor

    Unbolt 100hp 4-stroke Bolt on 80hp 2-stroke
  16. Scott Danforth

    Need Suggestions on Swim Step Support

    There isnt. However you could custom make something. I would find the nuts on the inside myself Or drill thru and use thru-bolts
  17. Scott Danforth

    Another 4.3 Timing Cover Leak Question

    FYI, in case you want some light readings https://forums.iboats.com/forum/engi...pdate?t=373060 https://forums.iboats.com/forum/engi...oil-leak-fixed https://forums.iboats.com/forum/engi...-bilge-finally
  18. Scott Danforth

    Need Suggestions on Swim Step Support

    That is a transom tie down We will need pics of your transom
  19. Scott Danforth

    Another 4.3 Timing Cover Leak Question

    Look up @achris thread on oil leak
  20. Scott Danforth

    Need Suggestions on Swim Step Support

    what is a normal ski tow eye? there are about 15 different ski tow eyes used over the years
Top