Search results

  1. flashback

    Clear hose

    Just posting back, I found the input hose was brittle at the thermostat housing but still soft and plyable an inch up stream so being shade tree, I cut the crispy end off and plugged it back on...I have a piece of clear and may put it in this winter but for now I will enjoy the summer..
  2. flashback

    Lifting Motor. Build Stand-Alone Gantry or Will This Work?

    A few diagonals and that should work fine. What's with the joist system Could you use the tractor, that might even be better..
  3. flashback

    14' fix

    Don't know what happened to the previous posts but I would think they deflect spray and you would want them...
  4. flashback

    Honda outboard BF 15

    Yes..
  5. flashback

    Gipsy - 1996 Sea Ray 210 Bowrider restomod

    I have a 95 weekender so I'm watching you..:)
  6. flashback

    Theft Prevention Tohatsu 15 hp Outboard Motor

    Unfortunately battery powered tools have made it easy.. guess you could take the motor off when you leave the boat...
  7. flashback

    Choosing first prop to run .

    That's sweet! Can't add anything but just wanted to say how nice your boat is and the motor sounds great...
  8. flashback

    very cool carb and intake manifold causing moisture

    Are you sure you have a working thermostat? The temp is way cool...
  9. flashback

    Honda BF75L cooling water issues

    I had a 1978 27ft oday sailboat with a BF75 and found the motor adequate to power the boat but it wasn't used often. I gave the boat to the boy scouts last month as a project. The motor still ran well but the boat needs love that I couldn't give it...
  10. flashback

    Close on the formula

    You'll make it fit!
  11. flashback

    Lowering the bunks . . .

    Back in the young days I was a rigger for a sailboat distributor mostly Hunter, Catalina and J boats and we sometimes had to launch in lakes that had no deep water. We would back in as far as we could, tie a stout line to the trailer and fire up the boat and back the whole rig until the boat...
  12. flashback

    1998 Four Winns 4.3 wont turn over

    Yep a boat that old you can bet that several electrical connections are corroded. My boat is a 95 model and I clean connections in my spare time.. eventually I'll get em...
  13. flashback

    Close on the formula

    Nothing I have found tastes good after brushing my teeth....:) You have your glass slipper and I hope it fits!
  14. flashback

    Popped through the intake.

    The slag on the points may be throwing the timing off enough to cause the popping..
  15. flashback

    Honda BF75L cooling water issues

    That diagram came from an old factory manual I have lying around from 1979..
  16. flashback

    Lowering the bunks . . .

    I'm probably missing something but how is an inch and a half gonna help? Your ramp must be almost level..
  17. flashback

    Fiberglass cracking - BRAND NEW R4 Surf 2023

    Sloppy layup schedule and a good chance that additional flaws will show up soon...
  18. flashback

    Need to check shutters… any tips?

    If you're confident in the condition of the elbow then do it leaving the elbow in place. Mine were rotten from rust so I got new ones..
  19. flashback

    Need to check shutters… any tips?

    I would loosen the clamps at the Y pipe remove the water feed hoses to the elbow then pull the elbow bolts and remove the elbow and down elbow as a single unit.. nothing gets misaligned so it will go back easy...
  20. flashback

    Replaced Bellows now gears won't engage fully?

    Yep I'm guessing that the bell crank and cable got separated during drive install..
View older results
Top