Search results

  1. C

    Remote oil tank

  2. C

    Remote oil tank

    sorrry to ask ..what is a 200 e200 stleub a 1997 200 hp Evinrude FICHT Tiller salty ? looks like a return line for retuning excess pumped oil from the FICHT crankcase oil injection system. see manual
  3. C

    Evinrude 7518

    I don't know what point you are at but may as well drop the gc and do an inspection and change impeller . check shift linkage components from shifter to LU try LU shift changes manually when finished with impeller. your shock absorber may need an inspection ( below WP housing) ...if...
  4. C

    Evinrude big twin 40

    some info... https://www.leeroysramblings.com/Johnson_35-40.htm
  5. C

    Rope Stuck on Evinrude 6HP outboard

    good eye ! and yes those piston are to clean !!
  6. C

    Rope Stuck on Evinrude 6HP outboard

    if you remove the LU does the FW turn by hand ? fyi https://www.leeroysramblings.com/OMC_6hp.htm
  7. C

    2000 Johnson 60 HP

    when it " only runs" at 4200 if you spray fuel in the carbs one after the other does the engine pick up rpms or fuel spray has no effect .? have you checked the exhaust passages has suggested. Tried a good decarb product like Merc POWER TUNE or similar Evinrude fuel system cleaner ...
  8. C

    2000 Johnson 60 HP

    OK so compression is ok...what is left just fuel or electrical issue. If the issue is constant..... light is at the end of the tunnel... I will look for the wire diagram but in the meantime... easy stuff first.. me I would look at electricals first starting with ignition KEY on power...
  9. C

    2000 Johnson 60 HP

    from where ?
  10. C

    96 Johnson 28SPL lower unit interchange?

    jmho... skeg looks ok if you were to polish up those welds on the plate, change oil fill washers (top/bottom) , fill and polish those holes with JB weld, and touch up any cracks and.....if no LU internal water ingress or damage to the LU gears a coat of paint will make it look like new !
  11. C

    Trim Problem

    relay control U-D switch contacts carry little current and less likely to carbon up compared to the load control contacts in the relays. if your system is like the above diagram relays are not very expensive to try out...... if you do not or can not go further VOM testing wise to find...
  12. C

    Manual Tilt Lock Kit?

    till u find info use a piece of wood (2x2) to keep it tilted up.
  13. C

    Trim Problem

    https://forums.iboats.com/threads/help-with-tilt-trim-wiring-1989-48-spl.546639/
  14. C

    Trim Problem

    switches do no carry much current and unlikely 2 sets (remote switch and switch on motor) would go bad . I don't have the wiring but I thinK one version supplies the DOWN current because it is lower than the UP current. easy /cheaper stuff first... check connections and measure volts at...
  15. C

    Trim Problem

    typically the U&D relays get activated up on down by the switches (12v) but the resulting blue-green feed to the T&T motor are direct power feeds from the battery B+and Ground simply switched out from the relays . first thing to do is check/clean all connections , cables, cable crimps...
  16. C

    I need help with my Johnson 9.9

    back to basics... you have sparks good you have compression good now it wants to be fed. clean the carb..all passages ALL passages blow dry check the float fill the carb and retry. open up #22 half a turn....retry check#4 tube if spraying some fuel mist in the carb face gets it...
  17. C

    Flywheel magneto draggs maggplate with it

    thanks for the feedback !
  18. C

    Flywheel magneto draggs maggplate with it

    picture above was just a ref. to align things does your fingernail snag or not .....going up-down the coil lamination face ? if yes you can expand the coil's bolt hole with a drill bit to allow you to back away from the rotating FW .
  19. C

    Flywheel magneto draggs maggplate with it

    see pic fingernail tip should not snag going up or down where the little arrow point (coil-boss junction)
  20. C

    1987 Johnson 15 HP Choke Linkage Hanging Up

    install any missing parts and see what happens... C clips are sold at good HW stores. Personally I think you are better off with the older carb...seems the newer plastic tops warp sometimes.
Top