Search results

  1. alldodge

    Tilt Trim 3 wire to 2 Wire conversion.

    Welcome Connect to same place where the Battery cable is connected. Your drawing doesn't show a breaker or fuse
  2. alldodge

    Francine, Kenner, La.

    Good to hear Kenny. Guess cable is like the phone, power goes out but phone keeps going
  3. alldodge

    Mercruiser 5.7mpi horizon single cylinder burning lean

    I'm still thinking that if it was a vacuum leak then there would be more then the one cylinder. To test use a vacuum gauge and connect with a Tee to the vac line that goes to regulator. Teeing with the Reg is going to be a real small line so may not respond very well
  4. alldodge

    Mercruiser 5.7mpi horizon single cylinder burning lean

    Another thought, if injector seal is not sealing tight then could be vacuum leak as nola mentioned. The issue is why isn't the leak effecting the nearby plugs (that is the puzzle)
  5. alldodge

    Mercruiser 5.7mpi horizon single cylinder burning lean

    My guess I think it's running for the most part fine. There is black around the plug and tip is real clean. The injector port is rusty (should not be) so there is moisture getting in some where. There should be no rust on the ports. Might have a small intake gasket leak which is steam cleaning...
  6. alldodge

    Mercruiser 3.0 cranks but wont start

    Volts at the Battery should be close to 12.7V Should see the real close to the same everywhere else. Only getting 8.4V then need to clean connections. Disconnect Battery cables then clean them. Leave cables disconnected and clean other ends on block and starter post. Pull the 10 pin engine...
  7. alldodge

    Boat trailer bunk bracket question

    ^^Agree Welcome Have not seen that type but could make them out of some steel flat stock, or from a welding shop
  8. alldodge

    Mercruiser 3.0 cranks but wont start

    Don't know what was buzzing other then the oil pressure switch turning on the buzzer. If it's the alarm buzzer then that's not an issue because it should sound until motor starts. The neutral safety switch is something that can make a good connection and also bad connection, just depends. With...
  9. alldodge

    Bravo 3 outdrive overhaul - propeller shaft seal questions

    The number(s) after the A in the part number just indicate another supplier was used. the 26- is another reference for Merc category. The parts are the same
  10. alldodge

    Bravo 3 outdrive overhaul - propeller shaft seal questions

    I remember buying a B3 lower reseal kit and it came with the older seals. The kit in your link looks like a B1 kit The B3 lower kit isn't much, and this kit is aftermarket. Unable to find a number for the Merc kit. I might just buy the seals individually.
  11. alldodge

    Mercruiser 3.0 cranks but wont start

    Welcome What is the motor serial number? Turn the key to start and hold it there while moving the throttle handle Fwd/Rev slightly. If it cranks when moving the handle then it's the neutral safety switch If it still does not crank, then use a voltmeter and measure the key switch on the Yel/Red...
  12. alldodge

    Bravo 3 outdrive overhaul - propeller shaft seal questions

    Note: A Bravo 3 lower is the same on a Standard B3 all the way to B3 X and XR. The upper housing is the only difference. Parts I listed are the correct ones. While even Mercruiser Parts list both seals (37 and 42) and item 37 as NLA if it's selected it shows 45 pieces in stock. My assumption...
  13. alldodge

    2002 5,7 Mercruiser exhaust manifold keeps cracking - 5 times this summer

    Never seen a set of injectors that were exactly matched to one another, even brand new, but then again they were not flow tested
  14. alldodge

    Mercruiser 5.7mpi horizon single cylinder burning lean

    With Pics working again, can you post the plug? It could be while running a tad lean, might not be enough to worry about
  15. alldodge

    Bravo 3 outdrive overhaul - propeller shaft seal questions

    New seals 1 each Small inner seal 26-8M0033407 (replaces 2 each lip seals) 1 each Large outer seal 26-861694 (replaces 2 each lip seals) Dimensions 3 - 3/8 OD, 2 - 1/2 ID, 13/16 wide Use manual 28 and on page 3D-26 it list removal tool as 91-862064A1 If you do not have the manual, then need to...
  16. alldodge

    Bravo 3 outdrive overhaul - propeller shaft seal questions

    Welcome To remove prop shaft both carrier and retainer must be removed. As mentioned in my thread I tried the slide hammer and was not able to get it out. I wound up splitting the seal to remove. Figured I would buy the correct tool and use a press if I needed to do it again Didn't have much...
  17. alldodge

    Mercruiser 4.3L - ignition fuse blowing

    5A being small look for another low current item Also is there another bilge pump
  18. alldodge

    2002 5,7 Mercruiser exhaust manifold keeps cracking - 5 times this summer

    ok, if you can see the crack then don't bother with testing
  19. alldodge

    Upholstery Decals falling off.

    Welcome Would suggest a vinyl type glue
  20. alldodge

    Mercruiser 4.3L - ignition fuse blowing

    Welcome Being 5A fuse and it blowing now after a heavy rain it's probably the bilge pump. Is there water in the bilge?
Top