Search results

  1. S

    1977 evinrude 15hp water flow

    Sounds normal....remember those are just exhaust relief holes, most of your exhaust is going through the prop.
  2. S

    Boat and motor given to me

    Maybe start with pulling the spark plugs, inserting some 2 stroke oil and hand cranking it 10 to 20 times. Could be locked up.
  3. S

    1957 fd-11 johnson skeg part number?

    Somehow I missed the big red sign! Sheesh.
  4. S

    1957 fd-11 johnson skeg part number?

    Weird really. I found this but not sure where it even is. https://www.nlamarine.com/products/johnson-evinrude-18hp-outboard-fd-12-1958-gear-case-382832-377117-lower-unit?variant=11287772677
  5. S

    1966 Jonhson 9.5 rust around exhaust cover

    Looks scorched to me.
  6. S

    1966 Jonhson 9.5 rust around exhaust cover

    Agree with above....I think it was overheated once. You might have issues so pulling the head, inspecting, resurfacing and installing a new gasket might be in order.
  7. S

    1982 Johnson 7.5hp Backfires but No Start (Wrong Carb?)

    Yes I agree, wires from mag need to be switched going to your coils. Should be orange blue to top perhaps. Does your motor have the airbox? And where is the choke knob? Motor still isn't running?
  8. S

    1988 48 special carbs

    His motor came with the 89 carbs on it and it didn't run right, it also came with parts including the 88 carbs. He rebuilt those so he now has the conclusions above.
  9. S

    My old Motor

    Lol, fair enough!
  10. S

    My old Motor

    My etec, which I bought brand new, is an amazing machine. The fuel economy makes it worth it alone. At the end of the day it's still just a motor so you take care of it just like any other motor. More sensors of coarse and the components cost more it sure runs nice. This is where the future...
  11. S

    O-ring on Vernatherm - 70HP, 2000 Johnson 3 cyl

    I don't see it shown or listed in any parts breakdown.
  12. S

    1992 40 Johnson carbs leaking

    Stuck float most likely.
  13. S

    Does this indicate water in lower unit oil?

    Behind the screw on the case, make sure it's not corroded up. Clean it up so the washer seats nice. No tape should be needed.
  14. S

    Does this indicate water in lower unit oil?

    Some oils look that way. If it's been sitting then water should come out first. Vacuum or pressure test to 15 lbs or so.....you can make a tool. You might be ok.
  15. S

    Lower unit

    Normal
  16. S

    short shaft outboard on a 21" transom

    Craigslist people constantly advertise the wrong shaft length. Have him measure from the bottom of the mount clamps to the top of the anti-ventalation plate.
  17. S

    Best way to free steering cable retainer nut stuck on tilt tube shaft

    I've had many issues with steering cables and such but not that exact issue. You should be able to get a pipe wrench on the other side to hold the tube while you spin the nut off on the other side. You could use jam nuts also.
  18. S

    Dry Firing Outboard

    I have a place with buoys to moor the boat....the neighbors kids dry fire the engine quite a bit and then lower the engine. They seem to be fine. Like was stated at low rpm? Probably fine. Other factors apply like age of the impeller.
  19. S

    Should I buy this Mercury 40 horse?

    Well, at least it was well cared for....<eyes rolling>
  20. S

    1982 Johnson 7.5hp Backfires but No Start (Wrong Carb?)

    I know, as I was writing he posted the success.
Top