Search results

  1. JASinIL2006

    Need confirmation of correct starter wire for ACR

    Hi all, I'm installing a Blue Sea ACR in my boat and one of the features is a starter isolation circuit. To use the isolation feature, I have to connect a terminal on the ACR to a positive line on either the the starter switch itself (which I'd rather avoid because of the length of the wire run)...
  2. JASinIL2006

    Question re: Alpha One upper unit

    Hi, I am helping a friend with a newly acquired boat, and last weekend we were changing the water pump. There was quite a bit of wear on the housing and it looked like the drive had been run without water a bit, we we replaced the whole pump housing, etc. I watched achris's video on changing an...
  3. JASinIL2006

    Main forum pages not updating?

    It seems like the main forum page (listing all the individual forums) and some of the pages below (e.g.,Boat Topics and Questions (not engine topics)) are not accurately reflecting new posts that have been made. For example, on the main page, the Boat Topics and Questions forum shows no new...
  4. JASinIL2006

    Forums ecxeptionally slow tonight?

    Is it just me, or are the forums running super slow tonight? It's taking 20-60 for every page load. Not seeing the slowness on other sites, so I don't think it's my connection...
  5. JASinIL2006

    Frequency of impeller replacement?

    While I'm sitting around being cold and hearing about the blizzard out East, I'd like to take care of any boat maintenance to keep me busy. In particular, I'm trying to figure out if I need to replace my impeller this off-season. The boat lives on a trailer and sees about 50-60 hours of use...
  6. JASinIL2006

    Won't accept post..."Invalid data"?

    Board is acting funky this morning... I just tried to reply to a thread, and after hitting the Post button and waiting for a few minutes for the "working" indicator to go away, I got a message saying my post wasn't made because of "Invalid data." I tried opening the thread in another window, and...
  7. JASinIL2006

    Tires for tow vehicle

    I'm getting close to needing new tires for my F-150 XLT Supercrew 4WD pickup. I'm looking for some info on truck tires.The last set I bought before we owned our boat, so I'm not sure how to take into consideration the fact that I now tow a boat around. Our boat is a 19' Larson SEI with a 350...
  8. JASinIL2006

    Construction of '93 or '94 Baretta?

    Hi all, a friend of mine is looking at project boats for a winter restoration, and I've agreed to help him look. We've found a '93 or '94 Baretta Success bowrider that is a candidate. It's been repowered with a 5.7 and a Volvo SX outdrive, but the floor and much of the upholstery is pretty bad...
  9. JASinIL2006

    Problem with Moeller Fluid Extractor - any ever see this?

    I was trying to winterize my boat this weekend and I pulled out my 5.0 L Moeller Fluid Extractor, and when I hooked everything up and started pumping, oil started coming out of the open ends of the T-handle on the pump! There was some residual oil in the bottom of the extractor, and since oil...
  10. JASinIL2006

    New NHL season!

    Anyone else excited about the new hockey season starting in a few days? I can't wait. I've missed hockey...
  11. JASinIL2006

    Power trim problems on Alpha 1 Gen 2

    Hi all, I'm having some problems with the power tilt/trim on my Alpha 1 Gen 2 drive. In addition to the controls at the helm (rocker switch for up/down, with a separate trailer button on the shaft of the throttle control), I installed a remote (genuine Mercruiser) switch on the transom. The...
  12. JASinIL2006

    Prop shop?

    I have a damaged aluminum 4-blade prop that I want to have repaired. (I've already ordered a stainless steel prop from iboats to be my primary prop). There are no prop shops near where I live (west central Illinois), so I think I will need someplace that does shipping. I googled for prop shops...
  13. JASinIL2006

    DIY repair on this prop?

    Trying to post from an iPad is about impossible... see question below...
  14. JASinIL2006

    Forums getting more stable?

    Is it just my good luck or are the forums starting to work better? I've been several times today, and no "page cannot be rendered" error, no problem advancing to the next page in a topic... it seems things are settling down. I still get the error message when posting a reply, but that seems to...
  15. JASinIL2006

    A good omen!

    OK, I take this as a very good omen... just as I was finishing a delicious lunch of Kung Pao Chicken at my desk, I visited iBoats and found the forums are back up; at exactly the same time, I opened my fortune cookie:
  16. JASinIL2006

    Water in trim fluid

    In prepping my boat for the season, I noticed the trim fluid was rather milky looking, so I extracted it from the reservoir, put it a jar, and sure enough, some water (a tablespoon or two) separated from the fluid. The manual recommends replacing and flushing the system, which I was planning to...
  17. JASinIL2006

    Aaargh! How to reach zerk on coupler?

    Hi, I'm in the midst of getting the boat ready for the season. I checked alignment and it looks great. Now I'm lubricating everything that needs lubed, and I am having a devil of a time finding/seeing the zerk on the coupler. I know there are two models, one with a zerk and one without, and I'm...
  18. JASinIL2006

    Boatinfo service manuals?

    Is anyone else having difficult accessing the Boatinfo service manuals? All the links I find to it on iBoats aren't working. Anyone else having this trouble?
  19. JASinIL2006

    Rehabbing my trailer...

    Re: Rehabbing my trailer... Finished up the trailer this weekend and got the boat back on it, with some help from my son. Now it's time to put the outdrive back on, de-winterize the engine and go boating! Thanks for all the advice and tips! Jim
  20. JASinIL2006

    Rehabbing my trailer...

    Re: Rehabbing my trailer... Almost done... painting is finished, I cleaned up some wiring for the electric brakes (complete rewiring is most likely a project for next year), and recarpeted the bunks. Now I just need to check the bearings (maybe) and adjust the brakes, and finish reassembly. I...
Top