Search results

  1. Lou C

    Wheel Bearing Inspection Interval

    With that system can you tell if water has entered the hub? Any of these systems are only as good as the seals; as long as I don’t see signs of moisture coming out if the expelled grease abs the bearings feel smooth when I spin the wheel I’m good.
  2. Lou C

    Wheel Bearing Inspection Interval

    I think the original axle that came with the trailer was like that I replaced it within a year or 2 with the first one Champion made for me.
  3. Lou C

    Wheel Bearing Inspection Interval

    PS: With the spindle lube every year after the boat is launched I always greased the bearings thoroughly & have never seen any sign of moisture or corrosion. If you take a sample of the grease and wet it you see it get milky right away the dark blue will get light blue. So that’s what I did for...
  4. Lou C

    Wheel Bearing Inspection Interval

    That Cherokee was never really a “Jeep” it was based on an Alfa Romeo platform. The problem with those was that they botched the ZF 9 speed auto trans programming it took them 3 model years to get it right. On my other Jeep (2007 Grand Limited 5.7) the only bearing part I had to replace was the...
  5. Lou C

    Wheel Bearing Inspection Interval

    Then there’s my ‘98 Jeep with the sealed front bearings. It’s 25 years old has 181,000 miles on it & still has the original bearings up front & they haven’t needed to be replaced, neither has any of the 6 ujoints…also “permanently lubricated”
  6. Lou C

    Wheel Bearing Inspection Interval

    Probably less than 5 lol! I live 1/4 mile from the water & the boat yard.
  7. Lou C

    RE: Issues with Mercruiser 5.0 LX 4 Barrel Carb

    Well on mine, I had blown HGs putting water in 2 cyls not enough to hydrolock but when I took the heads off it was obvious. The engine would start, run rough, then after about 5 min smooth out. When it cooled off they would get sticky again. You can also get rust on the stem, that for sure will...
  8. Lou C

    RE: Issues with Mercruiser 5.0 LX 4 Barrel Carb

    PPS I went back and looked at the beginning of this long thread and your exhaust elbows looked HORRIBLE, (way past replacement time) it seems quite likely that you had water leaking into your cyls, causing sticky valves, if the heads have not been off, do a leak down test and see what it shows...
  9. Lou C

    RE: Issues with Mercruiser 5.0 LX 4 Barrel Carb

    PS one hydraulic lifter being adjusted too tight can cause a valve not to close all the way and that can cause low compression. Heads were checked by a machine shop? It is common due to leaky inboard wet exhaust that you can have sticky valves causing lower compression.
  10. Lou C

    RE: Issues with Mercruiser 5.0 LX 4 Barrel Carb

    If one is at 80 psi that’s too low. A small block Chevy in good shape should have compression #s of approx 150; but it you did the comp test on a cold engine it would not be that accurate. Warm up engine set throttle wide open, remove spark plugs & disable ignition. After I replaced the cyl...
  11. Lou C

    Wheel Bearing Inspection Interval

    I had the same experience. 17 years with the first axle and 2 years with the second. When the drum brakes need service I change the seals & inspect the bearings. If I were dunking every week that would be different but this is a moored boat & the trailer only goes in salt water 2-4 times a year.
  12. Lou C

    4.3L OMC Cobra 1988 engine knock/rattle

    Exactly if you pull the drive & it’s quiet it could be a REALLY rusted gimble bearing or someone might have refilled the Cobra drive the wrong way and trashed the upper gear housing. Hopefully it’s the former not the latter
  13. Lou C

    1991 Sea Ray Bowrider 170 - Trying to remove bench seats and put in captains chairs. Is this possible?

    When I did my old '88 FW H-200 about 18 years ago....the square panels are the reinforcement for the pedestal seat mounts. Mine came with the pedestal seats so I just duplicated what was there.
  14. Lou C

    Bottom up restoration! MY FIRST BOAT

    Do you have a clear registration or title to the boat? Wouldn't want to do all that work, and then not be able to register it.
  15. Lou C

    Converting to Electric over Hydraulic this week

    Interested to see your impressions of the difference between standard surge brakes and EOH
  16. Lou C

    1993 Mercruiser 7.4 - Is my Problem Carb or Thunderbolt IV module

    If you have to use E-10 gas there are better quality accelerator pumps available from Cliff's High Performance, make sure you tell the shop the carb is for a boat.
  17. Lou C

    Roller trailer OK for aluminum boat?

    I’m think they use them in Australia but probably with more & smaller rollers than are used on US trailers
  18. Lou C

    Replacing 95 merc 4.3 with 87 OMC 4.3

    When I bought new Barr Marine manifolds and elbows to replace the one piece OMC V6 units, after I removed the paint they were perfect, couldn't even get a .001" feeler blade in under the straight edge anywhere. Here's what a new manifold looks like... one more tip, if re-using the old...
  19. Lou C

    Replacing 95 merc 4.3 with 87 OMC 4.3

    .003" feeler gauge I meant. Yesterday the forum was acting wacky lol. Volvo Penta published a document indicating how to check the sealing surfaces and how to re-surface properly.
  20. Lou C

    Replacing 95 merc 4.3 with 87 OMC 4.3

    They might be fine; the “official” way to check these is to lay a straight edge over them and see if you can fit a .003” in anywhere it should not fit, if they are really good a .001” won’t fit.
Top