Search results

  1. S

    Help

    Pee hole could be plugged, doesn't mean it got hot. Starter button worked before? If so, wire or fuse most likely. Racerone wanted model number, maybe he's on to something. Post model number.
  2. S

    Help

    Test wires from push switch for continuity. Is wire hooked up to soloniod correctly? Why do you say motor got hot? Did you melt a wire?
  3. S

    1995 Evinrude E40ELEO RPMs

    Those numbers are too high. Which pole setting is that?
  4. S

    84 Evinrude bogging full throttle surge

    I was going to add this and I forgot.
  5. S

    84 Evinrude bogging full throttle surge

    I don't think it's the prop with what your saying. When the prop slips your engine over revs and your boat slows. Is that happening? Doesn't sound like it. In the past others here have stated that you should look for a damaged wire, probably one under the flywheel that is shorting out when you...
  6. S

    2003 Evinrude 250 FICT - Stumped

    Here is a post in 2013 with a similar issue, a way to test (should be able to make sure pathways are connected) and then they list a place that repairs them. Have you ever plugged in a different control box just to see if that solves it? Anyhow, enjoy the read...
  7. S

    J150EXECD shift cable vs throttle cable

    Are those xtream cables as good as advertised? Claim to be smoother. Also, you left out one step, "test engine" ; )
  8. S

    84 Evinrude bogging full throttle surge

    If it's not the prop it's got to be fuel. If your using a boat fuel tank try and use a portable one.
  9. S

    Dry spark plugs?

    Viper, you have to look at the dates of the post, in this case 2007. Also, if you read the thread in his first post he doesn't have a choke. He has a primer. If you have a question or need support after reading an old posting, just start a new post.
  10. S

    Hooking up tach on 1992 Evinrude 40hp

    I've just read lots of testimony's of guys just turning the switch until the idle just matches up with their motors.
  11. S

    Hooking up tach on 1992 Evinrude 40hp

    Amps doesn't have anything to do with it, it's pickup points in one revolutions of the flywheel. I would think the directions of the tach would be correct.
  12. S

    Hooking up tach on 1992 Evinrude 40hp

    I don't think it will harm your tach if it's set wrong, it will just read incorrectly. You can then turn off the motor and set it to the other calibration. Don't trust me on this one though, let others confirm.
  13. S

    Hooking up tach on 1992 Evinrude 40hp

    2 cylinder motor under 70 hp should be a 10 pole.
  14. S

    J150EXECD shift cable vs throttle cable

    Glad you figured it out.
  15. S

    2003 Evinrude 250 FICT - Stumped

    Kill lanyard switch....another potential.
  16. S

    Drive shaft removal

    I've seen the home made puller jobies for the power head side but the gearcase side? It's bathed in oil?
  17. S

    J150EXECD shift cable vs throttle cable

    Ok, last post for me on this one. The part number you provide in the picture is one of the teleflex xtream cables. I couldn't find it. Teleflex and Seastar have joined each other and it looks like Sierra did to. I found Sierra teleflex cables with different part numbers. Quite a confusing go...
  18. S

    J150EXECD shift cable vs throttle cable

    The picture is not of a throttle cable and shifter cable, that is the old shifter cable and the new one. He says, if I'm interpreting this correctly, those are the orientations when they are both in the neutral positions.
  19. S

    J150EXECD shift cable vs throttle cable

    Mine also just run down the starboard side. To me, it would appear like you just installed it incorrectly in the box. Did you compare both ends before you installed? That would be the clincher.
Top