Search results

  1. 9

    2004 Yamaha 200 HPDI no neutral switch in morse control box how to bypass switch

    why would you bypass safety switches? fix it correctly, you controls should have a neutral switch. service manuals help a lot when working on motors you own, but not if the boat has controls that are not of the same make you could do a search for Yamaha wire color codes if you refuse to own...
  2. 9

    Yamaha 50TLRD revs and bogs revs and bogs...

    or just follow the testing procedures for the ignition system in the service manual for your motor testing the inputs and outputs of the CDI
  3. 9

    Yamaha 50TLRD revs and bogs revs and bogs...

    test the buzzer to make sure it functions as it should. if that works it should tell you low oil or overheat is not a possible problem if it does not buzz during the problem. timing light will show if spark is steady and if timing is advancing as it should when the problem shows up. have to...
  4. 9

    2008 Regal 1900 issue

    any you posted this in a Yamaha/Suzuki outboards forum, Why?
  5. 9

    2008 Regal 1900 issue

    VST is on fuel injected motors. carbs are not on fuel injected motors no one but you knows what motor you have, or did these boats only come with one kind/type/HP of motor?
  6. 9

    Looking for an electric starter kit for a 1997 20hp 2 stroke Yamaha

    find a motor you want/like and then sell your other motor to help offset the cost
  7. 9

    2008 hpdi series 2 high idle

    time to hook it up to YDS to see what the ECU does not like.
  8. 9

    Yamaha 50 tlr 2 stroke throttle stiff at engine

    sorry about that I thought you were talking about shifting. Could the new cable be in too tight of a bend at the motor when hooked up? I have run into that before
  9. 9

    Yamaha 50 tlr 2 stroke throttle stiff at engine

    I agree with you, but you are saying the motor is not running and you have a problem getting it into gear, so what are we suppose to think about your problem?
  10. 9

    Yamaha 50 tlr 2 stroke throttle stiff at engine

    my brothers C60 had a twisted shift shaft and bent pin thru the dog & prop shaft from someone trying to shift when not running or turning the shafts
  11. 9

    Suzuki 75hp

    just saying good or bad gear oil smells the same, it stinks
  12. 9

    Suzuki 75hp

    gear oil does not smell like regular oil and grease, it stinks
  13. 9

    2001 yamaha 9.9

    what 2001 9.9 are you talking about? what top hose is plugged. insects like to crawl into holes and plug them up. use weed wacker line to shove up that passage and blow with compressed air while running on muffs
  14. 9

    Suzuki 75hp

    never in my life have I known any gear oil to smell good, I have run some out boards without the lower units on as you said, but never played with a 75 Suzuki
  15. 9

    2001 F115 ISC idle speed control valve stickig

    are you talking about the rail pressure dropping to 10psi? if so either the VST is running out of fuel so the pump in there cannot pump anymore, the VST filter/screen is plugged up, or the pump is not running. does pumping the primer bulb help any to keep it running? if it does not then it...
  16. 9

    Suzuki 75hp

    that is correct, but some require putting into reverse instead of neutral so you can access the shaft nut to turn it not sure about a Suzuki
  17. 9

    2001 F115 ISC idle speed control valve stickig

    what you see on YDS is the request, it does not know if the ISC moves or not. do you hear the ISC rattle, resetting to 100% for next start up when you turn off the motor? if you hear it rattle then it is moving Yamaha recommends replacing instead of trying to clean it. it can overheat the...
  18. 9

    Suzuki df 15 4 stroke water leak?

    all leak some at the drive shaft, that is not a tight fit and there is no seal there but I do not think the pipe should be leaking set in that grommet
  19. 9

    Adding a Temp gauge

    you are just one person that feels that way about wanting one, that does not mean every boat and motor has to be sold with one. you want one, install it and go about your day
  20. 9

    2020 Yamaha 115 vmax cooling issue

    buy the Yamaha water pump kit, it is just a few dollars more then the impellor by itself and you get the new wear plat and cup and all o rings and gaskets needed. As I said before, your impeller is toasted. deformed and cracked it is not seating properly into the cup anymore. the wear plate...
Top